View CFD-G700CP_4286937.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

service manual sony corporation per sonal audio division published by sony techno create corporation us model CFD-G700CP canadian model cfd-g770cpk e model cfd-g770cp/g770cpk a ustralian model cfd-g770cpk cd radio cassette-corder 9-887-620-01 2007c16-1 ?2007.03 ve r. 1.0 2007.03 specifications CFD-G700CP/g770cp/ g770cpk model name using similar mechanism cfd-g505/g555cp/g555cpk cd cd mechanism type ksm-213cdp/c2np section optical pick-up type kss-213c t ape model name using similar mechanism hcd-ec50 section t ape transport mechanism type h21sb-c05 a udio power specifications (us) power output and total harmonic distortion w ith 3.2-ohm loads, both channels driven from 1 000 - 10 000 hz; rated 3 w per channel-minimum rms power, with no more than 10 % total harmonic distortion in ac operation. w oofer with 4-ohm loads, driven from 50 - 150 hz; rated 6 w minimum rms power, with no more than 10 % total harmonic distortion in ac operation. other specifications cd player section system compact disc digital audio system laser diode properties emission duration: continuous laser output: less than 44.6 w (th is output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) number of channels 2 frequency response 20 - 20 000 hz +1/? db wo w and fl utter below measurable limit radio section frequency range fm: 87.5 - 108 mhz am: 530 - 1 710 khz (g700cp: us/g770cpk: cnd, mx, e92) am: 531 - 1 611 khz (g770cpk: aus) am: 531 - 1 611 khz (9 khz step)(g770cp) am: 530 - 1 610 khz (10 khz step)(g770cp) antennas fm: telescopic antenna am: built-in ferrite bar antenna cassette-corder section recording system 4-track 2 channel stereo f ast winding time a pprox. 150 s (sec.) with sony cassette c-60 frequency response type i (normal): 70 - 13 000 hz general speaker full range: 10 cm (4 in.) dia., 3.2 ? , cone type (2) w oofer: 13 cm (5 1/8 in.) dia., 4 ? , cone type (1) tw eeter: 2 cm (13/16 in.) dia. (2) input built-in audio cable with stereo-mini plug: minimum input level 245 mv a udio in jack (stereo minijack): minimum input level 245 mv mic mix (microphone) jack (monaural minijack): sensitivity 2.5 mv, for low impedance microphone minimum input level 2.5 mv (g770cpk) outputs headphones jack (stereo minijack) f or 16 - 68 ? impedance headphones power output 4 w + 4 w (at 3.2 ? , 10% harmonic distortion) w oofer: 12 w (at 4 ? , 10% harmonic distortion) power requirements f or cd radio cassette-corder: 120 v ac, 60 hz (g700cp: us/g770cpk: cnd, mx, e92) 230 - 240 v ac, 50 hz (g700cp: sp) 230 v ac, 50 hz (g700cp: e41/g770cpk: aus) 12 v dc, 8 r20 (size d) batteries f or remote control: 3 v dc, 2 r6 (size aa) batteries power consumption ac 28 w photo : cfd-g770cpk ?continued on next page ? bbreviation au s: australian model cnd : canadian model e41 : ac 230v area in e model e92 : ac 120v area in e model mx : mexican model sp : singapore model
2 CFD-G700CP/g770cp/g770cpk battery life f or cd radio cassette-corder: fm recording sony r20p: approx. 6 h sony alkaline lr20: approx. 18 h t ape playback sony r20p: approx. 1.5 h sony alkaline lr20: approx. 6 h cd playback sony r20p: approx. 1 h sony alkaline lr20: approx. 4 h dimensions approx. 551 247 370 mm (w/h/d) (21 3 / 4 9 3 / 4 14 5 / 8 inches) (incl. projecting parts) mass a pprox. 8.4 kg (18 lb. 9 oz) (incl. batteries) supplied accessories ac pow er cord (1) remote control (1) design and specifications are subject to change without notice. notes on chip component replacement ? ev er reuse a disconnected chip component. notice that the minus side of a tantalum capacitor may be damaged by heat. flexible circuit board repairing ? eep the temperature of soldering iron around 270?c during repairing. do not touch the soldering iron on the same conductor of the circuit board (within 3 times). be careful not to apply force on the conductor when soldering or unsoldering. unleaded solder boards requiring use of unleaded solder are printed with the lead- free mark (lf) indicating the solder contains no lead. (caution: some printed circuit boards may not come printed with the lead free mark due to their particular size) : lead free mark unleaded solder has the following characteristics. ? unleaded solder melts at a temperature about 40 c higher than ordinary solder. ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. soldering irons using a temperature regulator should be set to about 350 c. caution: the printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! ? strong viscosity unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on ic pins, etc. ? usable with ordinary solder it is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. safety-related component warning!! components identified by mark 0 or dotted line with mark 0 on the schematic diagrams and in the parts list are critical to safe operation. replace these components with sony parts whose pa rt numbers appear as shown in this manual or in supplements published by sony. a ttention au composant ayant rapport ? la s?curit?! les composants identifi?s par une marque 0 sur les diagrammes sch?matiques et la liste des pi?es sont critiques pour la s?curit? de fonctionnement. ne remplacer ces com- posants q ue par des pi?es sony dont les num?ros sont donn?s dans ce manuel ou dans les suppl?ments publi?s par sony.
3 CFD-G700CP/g770cp/g770cpk t able of contents 1. servicing notes ............................................... 4 2. general ................................................................... 5 3. disassembly 3-1. disassembly flow ........................................................... 11 3-2. cabinet (upper) (1) section ............................................ 12 3-3. cabinet (upper) (2) section ............................................ 12 3-4. cabinet (front) section ................................................... 13 3-5. lcd board, audio in board, headphone board, power key board, microphone board (cfd-g770cpk), volume key board ...................... 13 3-6. front panel ...................................................................... 14 3-7. led board ...................................................................... 14 3-8. speaker (13cm) ................................................................ 15 3-9. speaker (10cm) ................................................................ 15 3-10. power board, battery board, d-light board (CFD-G700CP) ................................... 16 3-11. woofer key board, cd key board ......................... 17 3-12. tuner board ................................................................. 17 3-13. tape mechanism deck .................................................... 18 3-14. main board .................................................................... 18 3-15. cd block section ............................................................ 19 3-16. optical pick-up (ksm-213cdp/c2np) ......................... 19 3-17. tc board ......................................................................... 20 3-18. main belt, sub belt ......................................................... 20 4. test mode ............................................................... 21 5. mechanical adjustments ......................... 23 6. electrical adjustments .......................... 23 7. diagrams 7-1. block diagram ?tuner/cd section ....................... 28 7-2. block diagram ?main section ................................. 29 7-3. printed wiring board ?bd90 board .......................... 30 7-4. schematic diagram ?bd90 board ............................. 31 7-5. printed wiring board ?tuner board ....................... 32 7-6. schematic diagram ?tuner board ......................... 33 7-7. printed wiring board ?tc board ............................... 34 7-8. schematic diagram ?tc board ................................. 35 7-9. printed wiring board ?main board ......................... 36 7-10. printed wiring boards ?audio section .................... 37 7-11. printed wiring boards ?control section ............. 38 7-12. schematic diagram ?main (1/3), audio section .. 39 7-13. schematic diagram ?main section (2/3) ................. 40 7-14. schematic diagram ?main (3/3), control section .............................. 41 7-15. printed wiring boards ?power section .................. 42 7-16. schematic diagram ?power section ...................... 43 8. exploded views 8-1. overall section ................................................................ 51 8-2. cabinet (front) section ................................................... 52 8-3. cabinet (rear) section .................................................... 53 8-4. cabinet (upper) section-1 ............................................... 54 8-5. cabinet (upper) section-2 ............................................... 55 8-6. tape mechanism deck section ....................................... 56 9. electrical parts list .................................. 57
4 CFD-G700CP/g770cp/g770cpk section 1 servicing notes notes on handling the optical pick-up block or base unit the laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. during repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. the flexible board is easily damaged and should be handled with care. notes on laser diode emission check the laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. therefore, when checking the laser diode emission, observe more than 30 cm away from the objective lens. chuck plate jig on repairing on repairing cd section, playing a disc without the cd lid, use chuck plate jig. code number of chuck plate jig : x-4918-255-1 laser diode and focus search operation check 1. turn on the [power] button. 2. open the cd lid. 3. turn on sw2 with screwdriver, etc. as following figure. 4. press the u (cd) button. 5. confirm the laser diode emission while observing the objecting lens. when there is no emission, auto power control circuit or optical pick-up is broken. objective lens moves up and down three times for focus search. sw2 safety check-out after correcting the original service problem, perform the following safety check before releasing the set to the customer: check the antenna terminals, metal trim, ?etallized?knobs, screws, and all other exposed metal parts for ac leakage. check leakage as described below. leakage test the ac leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 ma (500 microamperes.). leakage current can be measured by any one of three methods. 1. a commercial leakage tester, such as the simpson 229 or rca wt-540a. follow the manufacturers instructions to use these instruments. 2. a battery-operated ac milliammeter. the data precision 245 digital multimeter is suitable for this job. 3. measuring the voltage drop across a resistor by means of a v om or battery-operated ac voltmeter. the ?imit?indication is 0.75 v, so analog meters must have an accurate low-voltage scale. the simpson 250 and sanwa sh-63trd are examples of a passive vom that is suitable. nearly all battery operated digital multimeters that have a 2 v ac range are suitable. (see fig. a) fig. a. using an ac voltmeter to check ac leakage. 1.5 k ? 0.15 f ac voltmete r (0.75 v) to exposed metal parts on set earth ground this appliance is classified as a class 1 laser product. the class 1 laser product marking is located on the rear exterior. laser component in this product is capable of emitting radiation e xceeding the limit for class 1.
5 CFD-G700CP/g770cp/g770cpk section 2 general this section is extracted from instruction manual. CFD-G700CP (1/2) basic operations * vol + (volume + on the remote) 2 , 0 and * (on the unit) have a tactile dot. before using the unit to turn on/o the power pr ess power ) . to adjust the volume pr ess vol +, C (volume +, C on the remote) 2 . to listen through headphones co nnect the headphones to the - (headphones) jack < . to select the sound characteristic pr ess rock, dance, salsa, reggaeton or flat , to select the kind of audio emphasis that you want. (on the remote, press sound , repeatedly.) to reinforce the bass sound pr ess power drive woofer (woofer on the re mote) 8 to select or on th e display. is more e ective. when the woo fer function works, the ring on the front panel lights up. to return to normal sound, press the button repeatedly until the indication disappears from the display. notes ? w hile the sleeping timer is on, the ring does not light, even if the woo fer function is used. ? wh en you use the headphones, the woofer function does not work. playing a cd/mp3 disc 1 pre ss push open/close 1 on the unit, and place a disc with the label side up on the cd compartment. to close the cd compartment, press push open/ close 1 on the unit. 2 pre ss on the unit ( on the remote) 0 . e unit plays all the tracks/mp3 les once. wh en you place mp3 discs, mp3 appears in the display a er the unit reads the le information. audi o cd tr ack number playing time mp3 disc mp3 le number after the song title is displayed, the playing time* will appear. * if the playing time is more than 100 minutes, it appears --:-- in the display. to pr ess pause playback on the unit ( on the remote) 0 . to resume play, press it again. stop playback 0 . go to the next track/mp3 le ? / . go back to the pr ev ious track/ mp3 le ? / . se lect a folder on an mp3 disc + to go forward and C to go backward . . locate a point whi le listening to the so und ? (forwa rd) or ? (backward) / while playing and hold it until you nd the point. ( or ? @ on the remote) locate a point whi le observing th e display ? (forwa rd) or ? (backward) / in pause and hold it until you nd the point. ( or ? @ on the remote) remove the cd push open/close 1 . tips ? playback starts from the track/mp3 le you last stopped playing (resume play). during stop, the track/mp3 le number to be played is displayed. ? to cancel the resume play (to start play from the beginning of the rst track/mp3 le), press 0 while the cd is stopped. when you op en the cd compartment or turn o the unit, the resume play is al so canceled. note yo u cannot locate a speci c track if shuf or pgm is lit in the display. press 0 , and then pr ess mode 6 repeatedly until shuf and pgm disappear from the display. example of folder structure and playing order e playing order of the folders and les is as follows: fo lder mp3 le notes on mp3 discs ? when th e disc is inserted, the unit reads all the les on that disc. during this time, reading is displayed. if there are many folders or non-mp3 les on the disc, it may take a long time for play to b egin or for the next mp3 le to start play. we recommend that you do not save unnecessary folders or les ot her than mp3 ones in the disc to be used for mp3 listening. ? a folder that does not include an mp3 le is skipped. ? ma ximum number of les: 255 ma ximum number of folders: 150 (including the root folder) ma ximum number of folders and les in total: 256 ma ximum directory levels: 8 ? fo lder names and le names can be displayed with up to 30 characters including quotation marks. ? e characters a - z, 0 - 9, and _ can be displayed on this unit. other characters are displayed as _. ? is unit conforms to version 1.0, 1.1, 2.2, 2.3 and 2.4 of the id3 tag format. wh en the le has the id3 tag information, song title, artist name and album name can be displayed. if the le does not have th e id3 tag information, no title appears instead of song title, n o artist appears instead of artist name and no album appears instead of album name. e id3 tag information can be displayed with up to 15 characters. ? wh en naming, be sure to add the le extension mp3 to the le name. ? if you put the extension mp3 to a le other than an mp3 le, the unit cannot recognize the le properly and will generate random noise that could damage your speakers. ? e le name does not correspond to the id3 tag. listening to the radio 1 pr ess radio/band ? auto preset - on the unit (radio/band - on the remote) repeatedly. ea ch time you press the button, the indication changes as follows: fm ? a m 2 hold down tune + or C . until the frequency digits begin to change in the display. e unit automatically scans the radio frequencies and stops when it nds a clear station. if you cannot tune in a station, press t une + or C . repeatedly to change the frequency step by step. when an fm stereo broadcast is received, st appears. tip if the fm broadcast is noisy, pr ess mode 6 until mono appears in th e display and the radio will play in monaural. playing a tape use buttons on th e unit for the operation. 1 pr ess * on the unit, and insert the tape into the tape compartment with the side you want to play facing upward. use type i (normal) tape only. close the compartment. ma ke sure there is no slack in the tape to avoid damaging the tape or the unit. 2 pr ess * on the unit. e unit starts playing. to pr ess pause playback * on the unit. to resume play, press it again. stop playback * on the unit. fas t-forward or rewind* or ? (rewind or fast forward) * on the unit. ej ect the cassette * on the unit. * when the tape is wound to the end, press * to release or ? * . recording on a tape use buttons on th e unit for the operation. 1 pr ess * on the unit to open the tape c ompartment and insert a blank tape with the side y ou want to record on facing upward. use type i (normal) tape only. close the compartment. 2 se lect the program source you want to record. to record from the cd player, press 0 on the unit an d place a cd. to record from the radio, tune in the station you want (see listening to the radio). 3 pr ess * on the unit to start recording ( is depressed automatically). to press paus e recording * on the unit. pr ess the button again to res ume recording. stop re cording * on the unit. tips ? ad ju sting the volume or the audio emphasis will not a ect the recordin g level. ? fo r the best results, use the ac power as a power source for recording. ? to erase a recording, proceed as follows: 1 insert the tape whose recording you want to erase. 2 make sure that tape is displayed. (if tape is not displayed, press * on the unit or press function > on the remote until it appears in the display.) 3 press * on the unit.
6 CFD-G700CP/g770cp/g770cpk CFD-G700CP (2/2) using the display yo u can check information about the cd using the display. c hecking the information of an audio cd to check the total track number and playing time of the cd pr ess 0 while the cd is stopped, and you can check th em in the display. to tal track number tota l playing time c hecking the information of an mp3 disc to check the total folder number and total le number on the cd pr ess 0 while the cd is stopped, and you can check th em in the display. to tal folder number to tal le number to check le information pr ess dspl/ent ; on the unit while playing an mp3 disc. e display changes as follows: e current le number and playing time ? ? e song title ( ) ? e artist name ( ) ? e album name ( ) playing tracks/mp3 les repeatedly (repeat play) yo u can play tracks/mp3 les repeatedly in normal, shu e or program play modes. 1 pr ess 0 . cd appears in the display. 2 pr oceed as follows. to repeat do this a single track/mp3 le 1 press repeat 5 until 1 appears. 2 press ? or ? / to select the track/ mp3 le that you want to repeat. 3 press 0 on the unit. all tracks/ mp3 les on th e cd 1 press repeat 5 until appears. 2 press 0 on the unit. a selected fo lder (mp3 disc only) 1 press mode 6 until appears, an d then press repeat 5 until appears. 2 select the folder by pressing + or C . . 3 press 0 on the unit. tracks/ mp3 les in random or der 1 select shu e play (see playing tracks/ mp3 les in random order). 2 press repeat 5 until shuf and appear. 3 press 0 on the unit. fi les in a selected fo lder in random or der (mp3 disc only) 1 start folder shu e play (see playing tracks/mp3 les in random order). 2 press repeat 5 on the unit until , s huf and appear. 3 press 0 on the unit. pr ogramed tracks/mp3 les 1 program tracks/mp3 les (see creating yo ur own program). 2 press repeat 5 until and pgm appear. 3 press 0 on the unit. on the remote use 0 instead of 0 . to cancel repeat play pr ess repeat 5 until disappears from the display. other operations playing tracks/mp3 les in random order (shu e play) yo u can play tracks/mp3 les in random order. when pl ay ing an mp3 disc, you can also play mp3 les in a se lected folder in random order (folder shu e play). 1 pr ess 0 . cd appears in the display. 2 pr ess mode 6 until shuf appears in the display. wh en you select folder shu e play (mp3 disc only), pr ess mode 6 on the unit until and shuf ap pe ar in the display. en press tune + or C . on the unit to select a folder you want. 3 pr ess 0 on the unit to start shu e play. on the remote use 0 instead of 0 . to cancel shu e play stop pl ayin g rs t. en press mode 6 until shuf disappears from the display. tips ? during shu e play, you cannot select the previous track/mp3 le by pr essing ? / . ? e resume function does not work during shu e play. creating your own program (program play) yo u can arrange the playing order of up to 15 tracks/mp3 les on a cd. 1 pr ess 0 . cd appears in the display. 2 pr ess mode 6 until pgm ashes in the display. 3 pr ess ? or ? / then press dspl/ent ; on the unit (enter a on the remote) for the tracks/mp3 les you want to program in the order you want. for mp3 les, press tune + or C . rst and then press ? or ? / and dspl/ent ; (enter a on the remote). a udio cd (program play) pr ogramed track number playing order mp3 disc (program play) pr ogramed le number playing order 4 pr ess 0 on the unit to start program play. on the remote use 0 instead of 0 . to cancel program play stop pl ayin g rs t. en press mode 6 until pgm disappears from the display. to delete the last track or le of the program pr ess clear ? on the remote while the unit is stopped. to check the order of tracks/mp3 les before play pr ess dspl/ent ; on the unit. ev ery time you press the button, the track number and th e playing order appear. to change the current program pr ess 0 once if the cd is stopped and twice if the cd is playing. e current program will be erased. en create a new program following the programing procedure. tips ? if you try to program 16 tracks/mp3 les or more, full will appear in the display. ? yo u can play the same program again, since the program is saved until you open the cd compartment or turn o the pow er of the unit. ? yo u can record your own program. a er you have created the pr ogram, insert a blank tape and press * on the unit to start recor ding. ? e resume function does not work during program play. presetting radio stations yo u can store radio stations into the units memory. you can preset up to 30 radio stations, 20 for fm and 10 for am in any order. 1 pr ess radio/band ? au to preset - on the unit to select the band. 2 hold down radio/band ? au to preset - on the unit for 2 seconds until auto ashes in the display. 3 pr ess dspl/ent ; on the unit. e stations are stored in memory from the lower fr equencies to the higher ones. if a station cannot be preset automatically yo u need to preset a station with a weak signal manually. 1 pr ess radio/band ? au to preset - on the unit to select the band. 2 tu ne in a station you want. 3 hold down dspl/ent ; on the unit for 2 seconds until the preset number ashes in the display. 4 pr ess preset + or C / on the unit until the preset number you want for the station ashes in the display. 5 pr ess dspl/ent ; on the unit. e new station replaces the old one. on the remote 1 pr ess radio/band - until the band you want appears in the display. 2 tu ne in a station you want. 3 hold down enter a for 2 seconds until the preset number ashes in the display. 4 pr ess preset + or C / until the preset number you want for the station ashes in the display. 5 pr ess enter a . tip e preset radio stations remain in memory even if you unplug the ac power cord or remove the batteries. playing preset radio stations 1 pr ess radio/band ? au to preset - on the unit to select the band. 2 pr ess preset + or C / on the unit to tune in the stored station. on the remote 1 pr ess radio/band - . 2 pr ess preset + or C / to tune in the stored station. fa lling asleep to music 1 play the music source you want. 2 pr ess sleep : to display sleep. 3 pr ess sleep : to select the minutes until the unit goes o automatically. ea ch time you press the button, the indication changes as follows: a uto* ? 60min ? 30min ? 20min ? 10min ? off. * when you select auto, the cd or tape stops playing in 90 minutes at most and the unit goes o automatically. when you ar e listening to the radio, the radio goes o in 90 minutes. if 4 seconds have passed a er you pressed sleep : , th e minutes in the display are entered. wh en the preset time has passed, the unit goes o au to ma tically. to c ancel the sleep function pr ess power ) to turn o the power. note wh en you are playing a tape using this function: if the tape length of one side is longer than the set time, the unit will not go o until the tape reaches the end. connecting optional component yo u can enjoy the sound from an optional component such as a portable digital music player through the speakers of this unit. be sure to turn o the pow er of each component before making any connections. fo r details, refer to the instruction manual of the component to be connected. built-in audio cable with stereo-mini plug audio connecting cable (not supplied) or (e.g.,por table digital music player) to a udio in jack to the line output jack 1 connect the built-in audio cable with stereo-mini plug 4 on the unit to the line output jack of the portable digital music player or other components*. 2 turn the unit and the connected component on. 3 pr ess audio in 6 on the unit and start playing sound on the connected component. e sound from the connected component is output from the speakers. * to connect the unit to a tv or vcr, use an extension cable (not supplied) with a stereo-mini jack on one end (for the built-in audio cable) and two phono plugs on the other end. recording the sound from the connected co mponent 1 insert a blank tape. 2 pr ess audio in 6 on the unit to display audio in. 3 pr ess * on the unit. recording starts. 4 play the optional component connected to the unit. tip sh ou ld the built-in audio cable 4 become damaged, you can use the audio in jack 3 to connect an optional component to the unit. use an audio connecting cable (not supplied) with a stereo mini plug on on e end (for the audio in jack 3 ). make sure the plug on the other end is suited to the jack on the optional component; for example, a stereo-mini plug for a portable digital music player, or two phono plug s for a tv or vcr. notes ? do not pull forcibly on the built-in audio cable 4 . doing so may cause the plug to rip o . ? co nnect the built-in audio cable 4 or audio connecting cable (not supplied) securely to prevent any malfunction. ? it is not possible to listen to two components connected at the same time through the built-in audio cable 4 and the audio in jack 3 (using an optional audio connecting cable). connect one component at a time. d-light sync out jack us e the d-light sync controller to connect to this d-light sync out jack + . you need to connect th e d-light sync controller to the lighting device* (not supplied). e lighting device will react according to control signals transmitted by the d-light sync controller upon receiving music source from the system. fo r details on the use of d-light sync controller an d lighting device, refer to the respective operating instructions supplied with the respective device. d-light sync controller cord of d -light sync controller (dsl-1) * refer to the d-light sync controller operating instruction for the re commended lighting device. note e lighting e ect may be di erent depending on the connected lighting device or the type of music being played back.
7 CFD-G700CP/g770cp/g770cpk cfd-g770cp (1/2) basic operations *vol + (volume + on the remote) 1 , / and * (on the unit) have a tactile dot. before using the unit to turn on/o the power pr ess power ) . to adjust the volume pres s vol +, C (volume +, C on the remote) 1 . to listen through headphones connect th e headphones to the - (headphones) jack ;. to select the sound characteristic pr ess rock, dance, salsa, reggaeton or flat + to select the kind of audio emphasis that you want. (on the remote, press sound + repeatedly.) to reinforce the bass sound pr ess power drive woofer (woofer on the re mote) 7 to select or on the disp lay. is more eective. when the woo fer function works, the ring on the front panel lights up. to retur n to normal soun d, pr ess the button repeatedly until the indication disappears from the display. notes ? whi le the sleeping timer is on, the ring does not light, even if the woo fer function is used. ? wh en you use the headphones, the woofer function does not work. playing a cd/mp3 disc 1 pr ess push open/close 0 on the unit, and place a disc with the label side up on the cd c ompartment. to c lose the cd compartment, press push open/ close 0 on the unit. 2 pr ess on the unit ( on the remote) / . e unit plays all the tracks/mp3 les once. wh en you place mp3 discs, mp3 appears in the display aer the unit reads the le information. audio cd tr ack number playing time mp3 disc mp3 le number after the song title is displayed, the playing time* will appear. *i f the playing time is more than 100 minutes, it appears --:-- in the display. to pr ess pause playback on the unit ( on the remote) / . to resume play, press it again. stop playback / . go to the next track/mp3 le ? . . go back to the previous track/ mp3 le ? . . select a folder on an mp3 disc + to go forward and C to go backward - . locate a point whi le listening to the so und ? (forward) or ? (backward) . while playing and hold it until you n d the point. ( or ? ? on th e remote) locate a point whi le observing the di splay ? (forward) or ? (backward) . in pause and hold it until you nd the point. ( or ? ? on the re mote) remove the cd push open/close 0 . tips ? playback starts from the t rack/mp3 le you last stopped playing (resume play). during stop, the track/mp3 le number to be played is displayed. ? to cancel the resume play (to start play from the beginning of the rst track/mp3 le), press / while the cd is stopped. when you op en the cd compartment or turn o the unit, the resume play is also ca nceled. note yo u cannot locate a specic track if shuf or pgm is lit in the display. pres s / , and then press mode 5 repeatedly until shuf and pgm disappear from the display. example of folder structure and playing order e playing order of the folders and les is as follows: folder mp3 le notes on mp3 discs ? wh en the disc is inserted, the unit reads all the les on that disc. during this time, reading is displayed. if there are many folders or non-mp3 les on the disc, it may take a long time for play to be gin or for the next mp3 le to start play. we recommend that you do not save unnecessary folders or les ot her than mp3 ones in the disc to be used for mp3 listening. ? a folder that does not include an mp3 le is skipped. ? m aximum number of les: 255 maximum number of folders: 150 (including the root folder) m aximum number of folders and les in total: 256 m aximum directory levels: 8 ? fo lder names and le names can be displayed with up to 30 cha racters including quotation marks. ? e characters a - z, 0 - 9, and _ can be displayed on this unit. other characters are displayed as _. ? is unit conforms to version 1.0, 1.1, 2.2, 2.3 and 2.4 of the id3 tag forma t. when the le has the id3 tag information, song title, artist name and album name can be displayed. if the le does not have th e id3 tag information, no title appears instead of song title, no artist appears instead of artist name and no album appears instead of album name. e id3 tag information can be displayed with up to 15 characters. ? wh en naming, be sure to add the le extension mp3 to the le name. ? if you put the extension mp3 to a le other than an mp3 le, the unit cannot recognize the le properly and will generate random noise that could damage your speakers. ? e le name does not correspond to the id3 tag. listening to the radio 1 pr ess radio/band ? auto preset , on the unit (radio/band , on the remote) repeatedly. each time you pres s the button, the indication changes as follows: fm ? a m 2 hold down tune + or C - until the frequency digits begin to change in the display. e unit automatically scans the radio frequencies and stops when it nds a clear station. if yo u cannot tune in a station, press t une +orC - repeatedly to change the frequency step by step. when an fm stereo broadcast is received, st appears. tip if th e fm broadcast is noisy, press mode 5 until mono appears in th e display and the radio will play in monaural. changing the am tuning interval if you n eed to change the am tuning interval, do the follow ing: 1 pr ess radio/band ? auto preset , on the unit until am is displayed. 2 pre ss dspl/ent : on the unit for 2 seconds. 3 pr ess radio/band ? auto preset , on the unit for 2 seconds. 9k step or 10k step ashes. 4 pr ess preset + or C . on the unit to select 9k step for 9 khz interval or 10k step for 10 khz interval. 5 pre ss dspl/ent : on the unit. aer changing the tuning interval, you need to reset your pres et am radio stations. playing a tape use button s on the unit for the operation. 1 pre ss * on the unit, and insert the tape into the tape compartment with the side you want to play facing upward. use type i (normal) tape only. close the compartment. make sure th ere is no slack in the tape to avoid damaging the tape or the unit. 2 pre ss * on the unit. e unit starts playing. to pr ess pause playback * on the unit. to resume play, pres s it again. stop playback * on the unit. fas t-forward or rewind* or ? (rewind or fast forward) * on the unit. e ject the cassette * on the unit. *wh en the tape is wound to the end, press * to release or ? * . recording on a tape use button s on the unit for the operation. 1 pre ss * on the unit to open the tape compartment and insert a blank tape with the side y ou want to record on facing upward. use type i (normal) tape only. close the compartment. 2 s elect the program source you want to record. to re co rd from the cd player, press / on the unit an d place a cd. to re co rd from th e radio, tune in the station you want (see listening to the radio). 3 pre ss * on the unit to start recording ( is depressed automatically). to pr ess pause re cording * on the unit. pres s the button again to resume recording. stop re cording * on the unit. tips ? ad ju st ing the volume or the audio emphasis will not aect the recor ding level. ? for th e best results, use the ac power as a power source for recor ding. ? to erase a recording, proceed as follows: 1inser t the tape whose recording you want to erase. 2make sure that tape is displayed. (if tape is not displayed, pres s * on the unit or press function = on the remote until it appears in the display.) 3press * on the unit.
8 CFD-G700CP/g770cp/g770cpk cfd-g770cp (2/2) using the display yo u c a n check information about the cd using the display. c hecking the information of an audio cd to check the total track number and playing time of the cd pres s / while the cd is stopped, and you can check them in the display. to tal track number total playing time c hecking the information of an mp3 disc to check the total folder number and total le number on the cd pres s / while the cd is stopped, and you can check them in the display. to tal folder number to tal le number to check le information pr ess dspl/ent : on the unit while playing an mp3 disc. e display changes as follows: e current le number and playing time ? ? e song title ( ) ? e artist name ( ) ? e album name ( ) playing tracks/mp3 les repeatedly (repeat play) yo u can play tracks/mp3 les repeatedly in normal, sh ue or program play modes. 1 pr ess / . cd appe ars in the display. 2 proce ed as follows. to repeat do this a single track/mp3 le 1press repeat 4 until 1 appears. 2press ? or ? . to select the track/ mp3 le that you want to repeat. 3press / on the unit. all tracks/ mp3 les on th e cd 1press repeat 4 until appears. 2press / on the unit. a selected fo lder (mp3 disc only) 1p ress mode 5 until appears, and then press repeat 4 until appears. 2select th e folder by pressing + or C - . 3press / on the unit. tracks/ mp3 les in random ord er 1select sh ue play (see playing tracks/ mp3 les in random order). 2press repeat 4 until shuf and appear. 3press / on the unit. fi les in a select ed fo lder in random ord er (mp3 disc only) 1s ta rt folder shue play (see playing tracks/mp3 les in random order). 2press repeat 4 on the unit until , s huf and appear. 3press / on the unit. prog ramed tracks/mp3 les 1p ro gram tracks/mp3 les (see creating your ow n program). 2press repeat 4 until and pgm appear. 3press / on the unit. on the remote use / instead of / . to c ancel repeat play pres s repeat 4 until disapp ears from the display. other operations playing tracks/mp3 les in random order (shue play) yo u can play tracks/mp3 les in random order. when pl ay ing an mp3 disc, you can also play mp3 les in a se lected folder in random order (folder shue play). 1 pre ss / . cd appe ars in the display. 2 pr ess mode 5 until shuf appears in the display. wh en you select folder shue play (mp3 disc only), press mode 5 on the unit until and shuf appear in the display. en press tune + or C - on th e unit to select a folder you want. 3 pre ss / on the unit to start shue play. on the remote use / instead of / . to cancel shue play stop playing rst. en press mode 5 until shuf disapp ears from the display. tips ? during shue play, you cannot select the previous track/mp3 le by pres sing ? . . ? e resume function does not work during shue play. creating your own program (program play) yo u can arrange the playing order of up to 15 tracks/mp3 les on a cd. 1 pre ss / . cd appe ars in the display. 2 pr ess mode 5 until pgm ashes in the display. 3 pre ss ? or ? . then press dspl/ent : on the unit (enter @ on the remote) for the tracks/mp3 les you want to program in the order you want. fo r mp3 les, press t une + or C - rst and then press ? or ? . and dspl/ent : (enter @ on the remote). audio cd (program play) pr ogramed track number playing order mp3 disc (program play) pr ogramed le number playing order 4 pre ss / on the unit to start program play. on the remote use / instead of / . to c ancel program play stop playing rst. en press mode 5 until pgm disappears from the display. to delete the last track or le of the program pr ess clear > on the remote while the unit is stopped. to check the order of tracks/mp3 les before play pr ess dspl/ent : on the unit. ever y time you press the button, the track number and the play ing order appear. to change the current program pres s / once if the cd is stopped and twice if the cd is playing. e current program will be erased. en create a new program following the programing procedure. tips ? if you try to program 16 tracks/mp3 les or more, full will appear in the display. ? yo u c a n play the same program again, since the program is saved until you open the cd compartment or turn o the power of the unit. ? yo u c a n record your own program. aer you have created the prog ram, insert a blank tape and press * on the unit to start recor ding. ? e resume function does not work during program play. presetting radio stations yo u c a n s t o r e radio stations into the units memory. you can preset up to 30 radio stations, 20 for fm and 10 for am in any order. 1 pr ess radio/band ? auto p reset , on the unit to select the band. 2 hold down radio/band ? auto preset , on the unit for 2 seconds until auto ashes in the display. 3 pr ess dspl/ent : on the unit. e stations are stored in memory from the lower fr equencies to the higher ones. if a station cannot be preset automatically yo u n eed to preset a station with a weak signal manually. 1 pr ess radio/band ? auto p reset , on the unit to select the band. 2 tu ne in a station you want. 3 hold down dspl/ent : on the unit for 2 seconds until the preset number ashes in the display. 4 pr ess preset + or C . on the unit until the preset number you want for the station ashes in the display. 5 pr ess dspl/ent : on the unit. e new station replaces the old one. on the remote 1 pr ess radio/band , until the band you want appears in the display. 2 t une in a station you want. 3 hold down enter @ for 2 seconds until the preset number ashes in the display. 4 pr ess preset + or C . until the preset number you want for the station ashes in the display. 5 pr ess enter @ . tip e preset radio stations remain in memory even if you unplug the ac power cord or remove the batteries. playing preset radio stations 1 pr ess radio/band ? auto p reset , on the unit to select the band. 2 pr ess preset + or C . on the unit to tune in the stored station. on the remote 1 pr ess radio/band , . 2 pr ess preset + or C . to tune in the stored station. f alling asleep to music 1 play the music source you want. 2 pr ess sleep 9 to display sleep. 3 pr ess sleep 9 to select the minutes until the unit goes o automatically. each time you pres s the button, the indication changes as follows: au t o* ? 60min ? 30min ? 20min ? 10min ? off. *wh en you select auto, the cd or tape stops playing in 90 minutes at most and the unit goes o automatically. when you ar e listening to the radio, the radio goes o in 90 minutes. if 4 seconds have passed aer you pressed sleep 9 , the minut es in the display are entered. wh en the preset time has passed, the unit goes o automati cally. to cancel the sleep function pr ess power ) to turn o the power. note wh en you are playing a tape using this function: if the tape length of one side is longer than the set time, the unit will not go o until the tape reaches the end. connecting optional component yo u c a n enjoy the sound from an optional component such as a portable digital music player through the speakers of this unit. be sure to turn o the power of each component before making any connections. for details, refer to the instruction manual of the component to be connected. built-in audio cable with stereo-mini plug audio connecting cable (not supplied) or (e.g .,portable digital music player) to audio in jack to the line output jack 1 c onnect the built-in audio cable with stereo-mini plug 3 on the unit to the line output jack of the portable digital music player or other components*. 2 tu rn the unit and the connected component on. 3 pre ss audio in 6 on the unit and start playing sound on the connected component. e sound from the connected component is output from the speakers. *to connect the unit to a tv or vcr, use an extension cable (not su pp lied) with a stereo-mini jack on one end (for the built-in audio cable) and two phono plugs on the other end. recording the sound from the connected c omponent 1 insert a blank tape. 2 pre ss audio in 6 on the unit to display audio in. 3 pre ss * on the unit. recording starts. 4 pl ay the optional component connected to the unit. tip sh ou ld the built-in audio cable 3 become damaged, you can use the audio in jack 2 to connect an optional component to the unit. use an audio connecting cable (not supplied) with a stereo mini plug on one end (for the audio in jack 2 ). make sure the plug on the other end is suited to the jack on the optional component; for example, a st ereo-mini plug for a portable digital music player, or two phono pl ugs for a tv or vcr. notes ? do not pull forcibly on the built-in audio cable 3 . doing so may cause the plug to rip o. ? co nnect the built-in audio cable 3 or audio connecting cable (not supp lied) securely to prevent any malfunction. ? it is no t possible to listen to two components connected at the same time through the built-in audio cable 3 and the audio in jack 2 (using an optional audio connecting cable). connect one component at a time.
9 CFD-G700CP/g770cp/g770cpk cfd-g770cpk (1/2) basic operations *vol + (volume + on the remote) 2 , 0 and * (on the unit) have a tactile dot. before using the unit to turn on/o the power pr ess power ) . to adjust the volume pres s vol +, C (volume +, C on the remote) 2 . to listen through headphones connect th e headphones to the - (headphones) jack <. to select the sound characteristic pr ess rock, dance, salsa, reggaeton or flat , to select the kind of audio emphasis that you want. (on the remote, press sound , repeatedly.) to reinforce the bass sound pr ess power drive woofer (woofer on the re mote) 8 to select or on the disp lay. is more eective. when the woo fer function works, the ring on the front panel lights up. to retur n to normal soun d, pr ess the button repeatedly until the indication disappears from the display. notes ? whi le the sleeping timer is on, the ring does not light, even if the woo fer function is used. ? wh en you use the headphones, the woofer function does not work. playing a cd/mp3 disc 1 pr ess push open/close 1 on the unit, and place a disc with the label side up on the cd c ompartment. to c lose the cd compartment, press push open/ close 1 on the unit. 2 pr ess on the unit ( on the remote) 0 . e unit plays all the tracks/mp3 les once. wh en you place mp3 discs, mp3 appears in the display aer the unit reads the le information. audio cd tr ack number playing time mp3 disc mp3 le number after the song title is displayed, the playing time* will appear. *i f the playing time is more than 100 minutes, it appears --:-- in the display. to pr ess pause playback on the unit ( on the remote) 0 . to resume play, press it again. stop playback 0 . go to the next track/mp3 le ? / . go back to the previous track/ mp3 le ? / . se lect a folder on an mp3 disc + to go forward and C to go backward . . locate a point whi le listening to the so und ? (forward) or ? (backward) / while playing and hold it until you n d the point. ( or ? @ on th e remote) locate a point whi le observing the di splay ? (forward) or ? (backward) / in pause and hold it until you nd the point. ( or ? @ on the re mote) remove the cd push open/close 1 . tips ? playback starts from the t rack/mp3 le you last stopped playing (resume play). during stop, the track/mp3 le number to be played is displayed. ? to cancel the resume play (to start play from the beginning of the rst track/mp3 le), press 0 while the cd is stopped. when you op en the cd compartment or turn o the unit, the resume play is also ca nceled. note yo u cannot locate a specic track if shuf or pgm is lit in the display. pres s 0 , and then press mode 6 repeatedly until shuf and pgm disappear from the display. example of folder structure and playing order e playing order of the folders and les is as follows: folder mp3 le notes on mp3 discs ? wh en the disc is inserted, the unit reads all the les on that disc. during this time, reading is displayed. if there are many folders or non-mp3 les on the disc, it may take a long time for play to be gin or for the next mp3 le to start play. we recommend that you do not save unnecessary folders or les ot her than mp3 ones in the disc to be used for mp3 listening. ? a folder that does not include an mp3 le is skipped. ? m aximum number of les: 255 maximum number of folders: 150 (including the root folder) m aximum number of folders and les in total: 256 m aximum directory levels: 8 ? fo lder names and le names can be displayed with up to 30 cha racters including quotation marks. ? e characters a - z, 0 - 9, and _ can be displayed on this unit. other characters are displayed as _. ? is unit conforms to version 1.0, 1.1, 2.2, 2.3 and 2.4 of the id3 tag format. wh en the le has the id3 tag information, song title, artist name and album name can be displayed. if the le does not have th e id3 tag information, no title appears instead of song title, no artist appears instead of artist name and no album appears instead of album name. e id3 tag information can be displayed with up to 15 characters. ? wh en naming, be sure to add the le extension mp3 to the le name. ? if you put the extension mp3 to a le other than an mp3 le, the unit cannot recognize the le properly and will generate random noise that could damage your speakers. ? e le name does not correspond to the id3 tag. listening to the radio 1 pr ess radio/band ? auto preset - on the unit (radio/band - on the remote) repeatedly. each time you pres s the button, the indication changes as follows: fm ? a m 2 hold down tune + or C . until the frequency digits begin to change in the display. e unit automatically scans the radio frequencies and stops when it nds a clear station. if yo u cannot tune in a station, press t une +orC . repeatedly to change the frequency step by step. when an fm stereo broadcast is received, st appears. tip if th e fm broadcast is noisy, press mode 6 until mono appears in th e display and the radio will play in monaural. playing a tape use button s on the unit for the operation. 1 pr ess * on the unit, and insert the tape into the tape compartment with the side you want to play facing upward. use type i (normal) tape only. close the compartment. make sure th ere is no slack in the tape to avoid damaging the tape or the unit. 2 pr ess * on the unit. e unit starts playing. to pr ess pause playback * on the unit. to resume play, pres s it again. stop playback * on the unit. fas t-forward or rewind* or ? (rewind or fast forward) * on the unit. e ject the cassette * on the unit. *wh en the tape is wound to the end, press * to release or ? * . recording on a tape use button s on the unit for the operation. 1 pre ss * on the unit to open the tape compartment and insert a blank tape with the side y ou want to record on facing upward. use type i (normal) tape only. close the compartment. 2 s elect the program source you want to record. to re cord from the cd player, press 0 on the unit an d place a cd. to record from the radio, tune in the station you want (see listening to the radio). 3 pre ss * on the unit to start recording ( is depressed automatically). to pr ess pause re cording * on the unit. pres s the button again to resume recording. stop re cording * on the unit. tips ? ad ju st ing the volume or the audio emphasis will not aect the recor ding level. ? for th e best results, use the ac power as a power source for recor ding. ? to erase a recording, proceed as follows: 1inser t the tape whose recording you want to erase. 2make sure that tape is displayed. (if tape is not displayed, pres s * on the unit or press function > on the remote until it appears in the display.) 3press * on the unit.
10 CFD-G700CP/g770cp/g770cpk cfd-g770cpk (2/2) using the display yo u c a n check information about the cd using the display. c hecking the information of an audio cd to check the total track number and playing time of the cd pres s 0 while the cd is stopped, and you can check them in the display. to tal track number total playing time c hecking the information of an mp3 disc to check the total folder number and total le number on the cd pres s 0 while the cd is stopped, and you can check them in the display. to tal folder number to tal le number to check le information pr ess dspl/ent ; on the unit while playing an mp3 disc. e display changes as follows: e current le number and playing time ? ? e song title ( ) ? e artist name ( ) ? e album name ( ) playing tracks/mp3 les repeatedly (repeat play) yo u can play tracks/mp3 les repeatedly in normal, sh ue or program play modes. 1 pr ess 0 . cd appe ars in the display. 2 proce ed as follows. to repeat do this a single track/mp3 le 1press repeat 5 until 1 appears. 2press ? or ? / to select the track/ mp3 le that you want to repeat. 3press 0 on the unit. all tracks/ mp3 les on th e cd 1press repeat 5 until appears. 2press 0 on the unit. a selected fo lder (mp3 disc only) 1p ress mode 6 until appears, and then press repeat 5 until appears. 2select th e folder by pressing + or C . . 3press 0 on the unit. tracks/ mp3 les in random ord er 1select sh ue play (see playing tracks/ mp3 les in random order). 2press repeat 5 until shuf and appear. 3press 0 on the unit. fi les in a select ed fo lder in random ord er (mp3 disc only) 1s ta rt folder shue play (see playing tracks/mp3 les in random order). 2press repeat 5 on the unit until , s huf and appear. 3press 0 on the unit. prog ramed tracks/mp3 les 1p ro gram tracks/mp3 les (see creating your ow n program). 2press repeat 5 until and pgm appear. 3press 0 on the unit. on the remote use 0 instead of 0 . to c ancel repeat play pres s repeat 5 until disapp ears from the display. other operations playing tracks/mp3 les in random order (shue play) yo u can play tracks/mp3 les in random order. when pl ay ing an mp3 disc, you can also play mp3 les in a se lected folder in random order (folder shue play). 1 pre ss 0 . cd appe ars in the display. 2 pr ess mode 6 until shuf appears in the display. wh en you select folder shue play (mp3 disc only), press mode 6 on the unit until and shuf appear in the display. en press tune + or C . on th e unit to select a folder you want. 3 pre ss 0 on the unit to start shue play. on the remote use 0 instead of 0 . to cancel shue play stop playing rst. en press mode 6 until shuf disapp ears from the display. tips ? during shue play, you cannot select the previous track/mp3 le by pres sing ? / . ? e resume function does not work during shue play. creating your own program (program play) yo u can arrange the playing order of up to 15 tracks/mp3 les on a cd. 1 pre ss 0 . cd appe ars in the display. 2 pr ess mode 6 until pgm ashes in the display. 3 pre ss ? or ? / then press dspl/ent ; on the unit (enter a on the remote) for the tracks/mp3 les you want to program in the order you want. fo r mp3 les, press t une + or C . rst and then press ? or ? / and dspl/ent ; (enter a on the remote). audio cd (program play) pr ogramed track number playing order mp3 disc (program play) pr ogramed le number playing order 4 pre ss 0 on the unit to start program play. on the remote use 0 instead of 0 . to c ancel program play stop playing rst. en press mode 6 until pgm disappears from the display. to delete the last track or le of the program pr ess clear ? on the remote while the unit is stopped. to check the order of tracks/mp3 les before play pr ess dspl/ent ; on the unit. ever y time you press the button, the track number and the play ing order appear. to change the current program pres s 0 once if the cd is stopped and twice if the cd is playing. e current program will be erased. en create a new program following the programing procedure. tips ? if you try to program 16 tracks/mp3 les or more, full will appear in the display. ? yo u c a n play the same program again, since the program is saved until you open the cd compartment or turn o the power of the unit. ? yo u c a n record your own program. aer you have created the prog ram, insert a blank tape and press * on the unit to start recor ding. ? e resume function does not work during program play. presetting radio stations yo u c a n s t o r e radio stations into the units memory. you can preset up to 30 radio stations, 20 for fm and 10 for am in any order. 1 pr ess radio/band ? auto p reset - on the unit to select the band. 2 hold down radio/band ? auto preset - on the unit for 2 seconds until auto ashes in the display. 3 pr ess dspl/ent ; on the unit. e stations are stored in memory from the lower fr equencies to the higher ones. if a station cannot be preset automatically yo u n eed to preset a station with a weak signal manually. 1 pr ess radio/band ? auto p reset - on the unit to select the band. 2 tu ne in a station you want. 3 hold down dspl/ent ; on the unit for 2 seconds until the preset number ashes in the display. 4 pr ess preset + or C / on the unit until the preset number you want for the station ashes in the display. 5 pr ess dspl/ent ; on the unit. e new station replaces the old one. on the remote 1 pr ess radio/band - until the band you want appears in the display. 2 t une in a station you want. 3 hold down enter a for 2 seconds until the preset number ashes in the display. 4 pr ess preset + or C / until the preset number you want for the station ashes in the display. 5 pr ess enter a . tip e preset radio stations remain in memory even if you unplug the ac power cord or remove the batteries. playing preset radio stations 1 pr ess radio/band ? auto p reset - on the unit to select the band. 2 pr ess preset + or C / on the unit to tune in the stored station. on the remote 1 pr ess radio/band - . 2 pr ess preset + or C / to tune in the stored station. f alling asleep to music 1 play the music source you want. 2 pr ess sleep : to display sleep. 3 pr ess sleep : to select the minutes until the unit goes o automatically. each time you pres s the button, the indication changes as follows: au t o* ? 60min ? 30min ? 20min ? 10min ? off. *wh en you select auto, the cd or tape stops playing in 90 minutes at most and the unit goes o automatically. when you ar e listening to the radio, the radio goes o in 90 minutes. if 4 seconds have passed aer you pressed sleep : , the minut es in the display are entered. wh en the preset time has passed, the unit goes o automati cally. to cancel the sleep function pr ess power ) to turn o the power. note wh en you are playing a tape using this function: if the tape length of one side is longer than the set time, the unit will not go o until the tape reaches the end. using the karaoke function (karaoke pon) is function reduces the vocal component of the sound source so that you can enjoy karaoke with your cds, tap es, radio programs, or audio in (the connected component). use button s on the unit for the operation. 1 connect a microphone (not supplied) to the mic mix + jack on the unit. if th e microphone has a power switch, set the switch to on. 2 pre ss power ) to turn on the unit. 3 pr ess karaoke pon + on the unit. e indicator beside the karaoke pon button + lights up. 4 pl ay the sound source. 5 turn mi c level + on the unit to adjust the microphone volume. to c ancel the karaoke function pres s karaoke pon + . notes ? m icrophones with a built-in echo function can cause a howling sound. keep the volume of the microphone low with the mic level control + . ? wh en the howling occurs, turn the head of the microphone away from the speakers. ? wh en recording from cds, radio programs, or audio in (the connected component) with the karaoke function is on, only the orig inal sound (with the vocal component) will be recorded on the tape. ? input from a microphone connected to the mic mix + jack cannot be re corded. ? ev en when the karaoke function is on, the vocal component may not be reduced or adequately reduced for some sound sources. connecting optional component yo u c a n enjoy the sound from an optional component such as a portable digital music player through the speakers of this unit. be sure to turn o the power of each component before making any connections. for details, refer to the instruction manual of the component to be connected. built-in audio cable with stereo-mini plug audio connecting cable (not supplied) or (e.g .,portable digital music player) to a udio in jack to the line output jack 1 c onnect the built-in audio cable with stereo-mini plug 4 on the unit to the line output jack of the portable digital music player or other components*. 2 tu rn the unit and the connected component on. 3 pre ss audio in 7 on the unit and start playing sound on the connected component. e sound from the connected component is output from the speakers. *to connect the unit to a tv or vcr, use an extension cable (not su pp lied) with a stereo-mini jack on one end (for the built-in audio cable) and two phono plugs on the other end. recording the sound from the connected c omponent 1 insert a blank tape. 2 pr ess audio in 7 on the unit to display audio in. 3 pr ess * on the unit. recording starts. 4 play the optional component connected to the unit. tip sh ou ld the built-in audio cable 4 become damaged, you can use the audio in jack 3 to connect an optional component to the unit. use an audio connecting cable (not supplied) with a stereo mini plug on one end (for the audio in jack 3 ). make sure the plug on the other end is suited to the jack on the optional component; for example, a stereo-mini plug for a portable digital music player, or two phono pl ugs for a tv or vcr. notes ? do not pull forcibly on the built-in audio cable 4 . doing so may cause the plug to rip o. ? co nnect the built-in audio cable 4 or audio connecting cable (not supplied) securely to prevent any malfunction. ? it is no t possible to listen to two components connected at the same time through the built-in audio cable 4 and the audio in jack 3 (using an optional audio connecting cable). connect one component at a time.
11 CFD-G700CP/g770cp/g770cpk section 3 disassembly 3-1. disassembly flow ? his set can be disassembled in the order shown below. 3-2. cabinet (upper) (1) section (page 12) 3-3. cabinet (upper) (2) section (page 12) set 3-11. woofer key board, cd key board (page 17) 3-4. cabinet (front) section (page 13) 3-6. front panel (page 14) 3-10. power board, battery board, d-light board (CFD-G700CP) (page 16) 3-7. led board (page 14) 3-9. speaker (10cm) (page 15) 3-5. lcd board, audio in board, headphone board, power key board, microphone board (cfd-g770cpk), volume key board (page 13) 3-8. speaker (13cm) (page 15) 3-12. tuner board (page 17) 3-14. main board (page 18) 3-15. cd block section (page 19) 3-16. optical pick-up (ksm-213cdp/c2np) (page 19) 3-13. tape mechanism deck (page 18) 3-17. tc board (page 20) 3-18. main belt, sub belt (page 20)
12 CFD-G700CP/g770cp/g770cpk note: f ollow the disassembly procedure in the numerical order given. 3-2. cabinet (upper) (1) section 3-3. cabinet (upper) (2) section 1 open the handle in the direction of the arrow. 3 open the cassette lid. 5 open the cd lid. 2 four screws (+ bv tapping (b3) ) 4 two screws (+ bv tapping (b3) ) 6 three screws (+ bv tapping (b3) ) qj handle 5 cnp391 (5p) 6 cnp301 (5p) 7 cnp393 (4p) qa cnp807 (2p) 8 cnp390 (6p) (g770cpk) 9 flexible flat cable (19core) (cn803) q; flexible flat cable (19core) (cn804) 3 1 close the cassette lid. qh cabinet (upper) section 4 open the cabinet (upper) section. qs cnp806 (2p) qd cnp803 (2p) qf cnp394 (3p) qg cnp391 (5p) 2 close the cd lid.
13 CFD-G700CP/g770cp/g770cpk 3-4. cabinet (front) section 3-5. lcd board, audio in board, headphone board, power key board, microphone board (cfd-g770cpk), volume key board 4 5 cabinet (front) section 1 battery li d 2 six screws (+ bv tapping (b3) ) 3 six screws (+ bv tapping (b3) ) qg micvolum knob qf microphone board 7 volume key board 5 button (tune) ql audio in board qk screw (+pwh tapping (b2.6)) qs power key board q; button (power) 3 screw (+pwh tapping (b2.6)) 1 two screws (+p tapping (b2.6)) 8 screw (+bv tapping (b2.6)) 9 screw (+pwh tapping (b2.6) ) 4 three screws (+bv tapping (b2.6)) 2 lcd board qh screw (+pwh tapping (b3)) qd two screws (+bv tapping (b3)) 6 qj headphone board qa (cfd-g770cpk)
14 CFD-G700CP/g770cp/g770cpk 3-6. front panel 1 fo ur screws (+bv tapping(b2.6)) 4 front panel 2 five screws (+bv tapping(b2.6)) 3 three screws (+bv tapping(b2.6)) 3-7. led board 2 ornamental ring 3 light guide ring 1 four screws (+bv tapping (b2.6)) 4 led 4 board 5 led 3 board 6 led 2 board 7 led 1 board claw claw claw claw
15 CFD-G700CP/g770cp/g770cpk 3-8. speaker (13cm) 2 speaker (13cm) 1 four screws (+bv tapping (b3)) 4 speaker (10cm) 2 two screws (+ bv tapping (b3) ) 3 two screws (+ bv tapping (b3) ) 7 speaker (10cm) 6 two screws (+ bv tapping (b3) ) 5 two screws (+ bv tapping (b3) ) 1 remove the solderings. 3-9. speaker (10cm)
16 CFD-G700CP/g770cp/g770cpk 2 cnp941 (4p) qa transformer bracket 0 power board qh screw (+pwh tapping (b3)) qj battery board 3 two screws (+bv tapping (b3)) 6 four screws (+bv tapping (b3)) 7 three screws (+bv tapping (b3)) qs four screws (+bv tapping (b3)) qf two screws (+bv tapping (b3)) 9 transformer holder 8 four screws (+bv tapping (b3)) 4 two screws (+bv tapping (b3)) 5 d-light board 1 sheet (rear) CFD-G700CP qd four terminal (+, ), batteries qg two terminal ( ), batteries 3-10. power board, battery board, d-light board (CFD-G700CP)
17 CFD-G700CP/g770cp/g770cpk 3-11. woofer key board, cd key board 1 cnp805 (3p) 3 cnp401 (2p) 7 cd key board 8 button (cd) 4 woofer key board 5 button (sound) 2 four screws (+ bv tapping (b2.6) ) 6 four screws (+ bv tapping (b2.6) ) 2 cnp1 (11 core) 4 tuner board 3 three screws (+ bv tapping (b3) ) 1 loosen the screw. 3-12. tuner board
18 CFD-G700CP/g770cp/g770cpk 2 cn303 (11 core) 1 three screws (+ bv tapping (b3) ) 4 tape mechanism dec k 3 cnp303 (6 core) 1 cnp1 (11 core) 6 three screws (+bv tapping(b3)) 2 cn303 (11 core ) 7 cn805 (21 core) 4 cnp805 (3p) 3 cnp303 (6p) 5 sw2 (2p) 8 main board 3-13. tape mechanism deck 3-14. main board
19 CFD-G700CP/g770cp/g770cpk 3-15. cd block section 2 flexible flat cable cn201 (21 core) 1 four screws (+ pwh tapping (b2.6) ) 3 cd block section 2 cd cover 1 two hooks 3-16. optical pick-up (ksm-213cdp/c2np)
20 CFD-G700CP/g770cp/g770cpk 1 screw 4 tc board 2 hook 3 remove soldering from the four points. tc board yellow red white black 1 two screws ( +bind dt m2 6) 2 hook 3 motor assy (m971) 4 main belt (b1) 5 sub belt (b1) 3-17. tc board 3-18. main belt, sub belt
21 CFD-G700CP/g770cp/g770cpk section 4 test mode [mc cold reset] the cold reset clears all data including preset data stored in the memory to initial conditions. execute this mode when returning the set to the customer. procedure: 1. in the standby status, press the power button to turn the power on. 2. press three buttons of x , mode and at last power si- multaneously. 3. when ?eset?appears, the machine enters standby status. [panel test mode] enter the panel test mode procedure: 1. in the standby status, press the power button to turn the power on. 2. press three buttons of repeat , x , and dspl/ent si- multaneously. 3. when the panel test mode is activated, leds and segments of lcd are all turned on. ver sion check procedure: 1. in the panel test mode (all leds and segments of lcd are turned on), press the rock button. 2. on the lcd, date and version are displayed ?xxxxxxx? f or example, ?127v103? 3. from this status, press the dance button, and the destination is displayed. for example, ?014 au6?or ?014 u2 4. to release from this mode, press three buttons of repeat , x , and dspl/ent simultaneously. [change-over the am tuning interval] (g770cp) the am tuning interval can be changed over 9 khz or 10 khz. procedure: 1. press the power button to turn the power on. 2. press the radio/band button to select tuner (am) function. 3. select the am band mode and press the dspl/ent button for an extended time in the am band state. 4. then, press the auto preset/radio/band for an e xtended time. 5. next, press the preset + preset ? button select either 9k/10k. 6. finally, press the dspl/ent button to set the selected step. [cd service mode] this mode can move the sled of the optical pick-up, and also can turn the optical pick-up laser power on and off. procedure: 1. press the power button to turn the power on. 2. press three buttons of x , vol + , and salsa simulta- neously. 3. it enters the cd service mode and displays ?ervice? 4. to exit from this mode, press three buttons of x , vol + , and salsa simultaneously. ke y operation: preset+ > , preset? . : use these keys to move the sled. when preset+ > is pressed in this mode, the sled moves to outer circumference and the message ?led out?is displayed. when preset? . is pressed in this mode, the sled moves to inner circumference and the message ?led in?is displayed. mode : use this key to turn the optical pick-up laser power on and off. when the laser power is turned on, the message ?d on?is displayed. when the laser power is turned off, the message ?d off?is displayed. [cd error code] the past errors of the optical pick-up system (= optical unit + bd board) is displayed as the bd errors as shown below. procedure: 1. press the power button to turn the power on. 2. press three buttons of vol + , x and dance simulta- neously. 3. then, the bd error code is displayed as ?0xxxxxx?(x means hexadecimal number) on the lcd screen as shown below. 4. every pressing of the preset+ > b utton in this mode increments the number after ??starting from ?0?up to ?4? and then returns to ?0? every pressing of the preset? . b utton in this mode decrements the number after ?? the smaller the error code number is, the newer the error content is. 5. to exit from this mode, press the power button to turn the power off.
22 CFD-G700CP/g770cp/g770cpk contents of ?d errors error display example d 0 02 09 01 1 234 1 it indicates the error history number 0 to 4: the error code number 0 indicates the newest error. 2 it indicates the error content 01: the focus servo cannot lock-in. 02: gfs is no good (ng). 03: the startup time exceeds the specified period of time (time ov er) 04: the focus servo is unlocked continuously. 05: q code cannot be obtained within the specified period of time. 06: the tracking servo cannot lock-in. 07: blank disc 3 it indicates the on-going processing of optical pick-up system (= optical unit + bd board) when the trouble has occurred. 01: the cd ship mode processing is in progress. 02: the power off processing is in progress. 03: the initialize processing is in progress. 04: the optical pick-up system (= optical unit + bd board) is in the stop state. 05: the stop operation is in progress. 06: the startup processing is in progress. 07: the toc read-in processing is in progress. 08: the search operation is in progress. 09: the play operation is in progress. 0a: the pause operation is in progress. 0b: the play ?manual search operation is in progress. 0c: the pause ?manual search operation is in progress. 4 it indicates the operation that is being processed when the trouble has occurred. it indicates the step number of each processing specified by 3 . because the numbers of steps are different in each processing, this number is different in each processing.
23 CFD-G700CP/g770cp/g770cpk ? precaution 1. clean the following parts with a denatured-alcohol-moistened swab : record/playback head pinch roller erase head rubber belts capstan idlers 2. demagnetize the record/playback head with a head demagnetizer. (do not bring the head magnetizer close to the erase head.) 3. do not use a magnetized screwdriver for the adjustments. 4. after the adjustments, appiy suitable locking compound to the parts adjusted. 5. the adjustments should be performed with the rated power supply voltage unless otherwise noted. ? tor que measurement ? t ape tension measurement mode tension meter meter reading fwd cq-403a more than 80 g ?cm (more than 2.82 oz ?inch) 2.0 ?8.0 mn ?m (20 to 80 g ?cm) (0.28 ?1.12 oz ?inch) 0.15 ?0.6 mn ?m (1.5 to 6 g ?cm) (0.021 ?0.083 oz ?inch) 5 ?17.7 mn ?m (50 to 177 g ?cm) (0.7 ?2.48 oz ?inch) 5 ?17.7 mn ?m (50 to 177 g ?cm) (0.7 ?2.48 oz ?inch) cq-102as cq-102c cq-201as cq-201b mode fwd fwd back tension ff rew tor que meter meter reading section 6 electrical adjustments section 5 mechanical adjustments checking location: + bd90 board tp (rfi) tp (vc) oscilloscope (dc range) procedure : 1. connect oscilloscope to tp (rfi) and tp (vc) on the bd90 board. 2. press the power button to turn the power on, and press the z push open/close button to open the cd disc tray. 3. set disc (yeds-18) on the tray and press the u (cd) button to playback. 4. confirm that oscilloscope waveform is as shown in the figure below. (eye pattern) a good eye pattern means that the diamond shape ( ? ) in the center of the waveform can be clearly distinguished. volt/div: 200 mv time/div: 500 ns level: 1.2 0.3 vp-p tp (vc) tp (rfi) ic101 ?bd90 board (side b) cd section note: 1. cd block is basically constructed to operate without adjustment. 2. use yeds-18 disc (3-702-101-01) unless otherwise indicated. 3. use an oscilloscope with more than 10 m ? impedance. 4. clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. 5. check the focus bias check when optical pick-up block is replaced. focus bias check
24 CFD-G700CP/g770cp/g770cpk adjustment location: tape speed adjustment control inside motor (m971) i jack (j391) set 32 ? test tape ws-48a (3 khz, 0 db) digital frequenc y counter ?test tape t ype signal used for ws-48a 3 khz, 0 db tape speed adjustment t ape speed adjustment procedure: mode: playback adjust so that the value on the digital frequency counter is 3,000 hz. specification value: digital frequency counter 2,940 to 3,060 hz adjust so that the frequency at the beginning and that at the end of tape winding are between 2,970 to 3,030 hz. adjustment location: record/playback/erase head record/playback head azimuth adjustment procedure: 1. mode: playback 2. tu rn the adjustment screw and check output peaks. if the peaks do not match for l-ch and r-ch, turn the adjustment screw so that outputs match within 1db of peak. 3. mode: playback 4. after the adjustments, apply suitable locking compound to the pats adjusted. screw position l-ch peak within 1db output level l-ch peak r-ch peak within 1db screw position r-ch peak 0 db=0.775 v set i jack (j391) + level meter test tape p-4-a063 (6.3 khz, ? 10 db) 1. demagnetize the record/playback head with a head demagnetizer. 2. do not use a magnetized screwdriver for the adjustments. ? t est tape t ape signal used for p-4-a063 6.3 khz, ?0 db azimuth adjustment set test tape p-4-a063 (6.3 khz, ? 10 db) oscilloscope v h waveform of oscilloscope in phase 45 90 135 180 good wrong i jack (j391) t ape section
25 CFD-G700CP/g770cp/g770cpk am if adjustment adjust for a maximum reading on level meter. t1 450 khz am frequency coverage adjustment (sp, e41, aus) frequency display 531 khz 1,611 khz reading on digital voltmeter 1.0 0.05 v 5.0 0.7 v adjustment part l4 am frequency coverage adjustment (except sp, e41, aus) frequency display 530 khz 1,710 khz reading on digital voltmeter 1.0 0.05 v 5.2 0.7 v adjustment part l4 am tracking adjustment (sp, e41, aus) adjust for a maximum reading on level meter. l3 ct3 621 khz 1,404 khz am tracking adjustment (except sp, e41, aus) adjust for a maximum reading on level meter. l3 ct3 620 khz 1,400 khz fm if adjustment adjust for a maximum reading on level meter. t2 10.7 mhz fm frequency coverage adjustment frequency display 87.5 mhz 108 mhz reading on digital voltmeter 1.3 0.3 v 3.0 0.2 v adjustment part l2 fm tracking adjustment adjust for a maximum reading on level meter. l1 ct1 87.5 mhz 108 mhz adjustment location: see page 26. tuner section 0 db = 1 v am section setting: radio band?uto preset button: am ? epeat the procedures in each adjustment several times, and the tracking adjustments should be finally done by the trimmer capacitors. remove fm antenna in fm adjustment. fm section setting: radio band?uto preset button: fm am rf signal generator 30% amplitude modulation by 400 hz signal output level: as low as possible put the loop antenna close to the set. + level meter set 32 ? i jack (j391) fm rf signal generator 75 khz frequency deviation by 1 khz signal output level: as low as possible + level meter set 32 ? 0.01 f tuner board tp (gnd) tuner board tp-ant(jw2) i jack (j391) digital voltmeter tp (cv) tp (gnd) 100 k ? tuner board
26 CFD-G700CP/g770cp/g770cpk adjustment location: l3,ct3 am tracking adjustmen t l1,ct1 fm trackng adjustment l2 fm frequency coverage adjustment l4 am frequency coverage adjustment tp-ant (jw2) l3 ic1 ct3 ct1 l4 l2 t2 t1 l1 ?tuner board (component side) tp (gnd) tp (cv) tp-ant jw2 ?tuner board (conductor side) t1 am if adjustment t2 fm if adjustment
27 27 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk circuit boards location section 7 diagrams for schematic diagrams. note: all capacitors are in f unless otherwise noted. (p: pf) 50 wv or less are not indicated except for electrolytics and tantalums. all resistors are in ? and 1 / 4 w or less unless otherwise specified. ? f : internal component. c : panel designation. h : adjustment for repair. a : b+ line. ? oltages and waveforms are dc with respect to ground un- der no-signal (detuned) conditions. ?bd90 board no mark : cd play ?tuner board no mark : fm (): am ?tc board no mark : fm (): pb <>: rec []: cd play ?other boards no mark : cd play ? oltages are taken with a vom (input impedance 10 m ? ). v oltage variations may be noted due to normal production tolerances. ? av eforms are taken with a oscilloscope. v oltage variations may be noted due to normal production tolerances. circled numbers refer to waveforms. signal path. f : fm f : am e : t ape play a : t ape rec j : cd d : line in ?b breviation au s: australian model. cnd : canadian model. e41 : ac 230 v area in e model. e92 : ac 120 v area in e model. mx : mexican model. sp : singapore model. for printed wiring boards. note: x : parts extracted from the component side. y : parts extracted from the conductor side. w : indicates side identified with part number. ? f : internal component. : p attern from the side which enables seeing. (the other layers' patterns are not indicated.) indication of transistor. this note is common for printed wiring boards and schematic diagrams. (in addition to this, the necessary note is printed in each block.) caution: p attern face side: parts on the pattern face side seen from (side b) the pattern face are indicated. par ts face side: parts on the parts face side seen from (side a) the parts face are indicated. c b these are omitted. e q b these are omitted. ce q b these are omitted. c q e note: the components identi- fied by mark 0 or dot- ted line with mark 0 are critical for safety. replace only with part n umber specified. note: les composants identifi?s par une marque 0 sont cri- tiques pour la s?curit?. ne les remplacer que par une pi?ce portant le num?ro sp?cifi?. tc board tuner board cd key board a udio in board led2 board led4 board led1 board led3 board lcd board w oofer key board bd90 board power board main board headphone board power key board microphone board (cfd-g770cpk only) d-light board (CFD-G700CP only) v olume key board battery board
28 28 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-1. block diagram ?tuner/cd section o-tu-ce 22 o-tu-clk 24 o-tu-di 25 i-tu-do 23 system controller ic801(1/2) 10 lid-open sw2 19 l1 l3 ferrite-rod antenna d1 d11 d10 2 24 21 22 20 fm mix fm rf in fm rf out fm osc am rf in am osc fm osc am mix am osc osc out 4 mix out 16 if buffer cf2 cf4 7 6 fm if-in am if-in fm mpx fm/am buffer fm det am det 15 a det out 17 mute 12 11 r-ch r-ch 10 fm/am front-end if amp,det,fm mpx 23 5 radio 6v quad vcc1 vcc2 main section (page 29) t2 ce 12 11 14 13 14 13 mo/st band 10 4 2 3 1 20 19 fm/am pll ic2 fm in am in vdd xout xin cl di do if in mo/st 6v x1 75khz tu-l radio 6v ct1 l2 d2 radio 6v ct3 radio 6v d3 l4 antenna fm telescopic ic1 t1 18 lp out 1vdd cd+3.3v cd+1.5v 5 vout 16 pd 18 st ind 8 st ind 7 band ifout mpx-in o-tu-mute 26 radio 6v ant1 17 lp in l1, ct1 fm tracking l2 fm frequency coverage l3, ct3 am tracking l4 am frequency coverage t1 am if t2 fm if b main section (page 29) optical pick-up block (ksm-213cdp) automatic power controller q301 +1.7v +3.3v ld gnd focus coil f+ f t+ t sp+ sp sl+ sl tracking coil ic401 s201 (limit) x102 16.934mhz +3.3v sl/sp motor driver ic101 rf amp,dsp,mp3 ic201 +1.5v reg 26 20 27 18 17 vr pd 2 1 12 11 3 24 7mute m m (spindle) (sled) vcc vc a b c d e f detector fn11(a) fp11(b) tn1(e) 100 tp1(f) 98 ldo 91 42 13 20 10 21 9 buck(clk) rst cce p100 sbsy 27 ro 30 lo 24 xo 23 xi 95 97 fn12(c) 94 fp12(d) 96 cd-l 12 11 9 23 bus3 40 41 42 43 48 54 37 bus2 39bus1 38bus0 buck(clk) i-mp3-rst o-mp3-ccen i-mp3-req i-mp3-sbsy i/o-mp3-bus3 7 8 17 18 3 43 19 i/o-mp3-bus2 6 i/o-mp3-bus1 5 i/o-mp3-bus0 o-mp3-m-mute 4 focus/tracking coil driver 15 16 12 11 10 13 14 9 7 8 5 6 4 1 3 2 m401 m402 vd4+ vd4- vd3+ vd3- vo1+ vo1- vo2- vo2+ in1 in2' in3' bias in4' ioo(/mso) dmo fmo tro vref f0o i01(/uhs0) md1 push open/close : fm : am : cd ?signal path ?r-ch is omitted due to same as l-ch.
29 29 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-2. block diagram ?main section : fm : cd ?signal path ?r-ch is omitted due to same as l-ch. : tape play : tape rec : line in 20 b a tuner/cd section (page 28) cd-l g770cpk g770cpk tu-l r-ch r-ch record/playback head hrp301 he301 erase head r-ch r-ch l-ch rec bias osc q301 rec/pb pre amp ic301 mic mix amp ic401 5 4 15 21 rec tape l.lin l.rad pb amp 26db 24 22 l.ld tape tape t301 12 mute q171 amp q321 switch q951 d461 q351 agc 3 8 stby power amp ic371 r-ch j391 speaker (l-ch) speaker (r-ch) s401,402,405, s406,413,414 q801,804,815,816 led drive q805 key wake up o-vol-data 31 o-a-mute 57 o-tape 12 tape rec ic801(2/2) system controller 93 92 x802 5.53mhz x0 x1 1 clk-shift am 2 clk-shift fm s301 rec/pb rec amp amp buffer 7db 11 tape play m m971 capstan/reel motor s972 motor s971 play tuner/cd section (page 28) 17 line 55 o-cd-sw 37 i-mic-in 46 o-buf-cont 6 ref i-key-1 39 i-key-2 40 woofer led1 29 woofer led2 30 q451,452 clk shift s404,407,411, s412,418,420 eeprom-sck 50 eeprom-sda 49 6 5 eeprom ic802 l1-in l2-in l-igout l-out 5 lin l-r l+r sw1 logic l r 6 3 15 16 mute 27 22 33 8 l-volin data clk 4 sound/volume ic321(2/2) input select ic321(1/2) 9 o-vol-clk 21 34 agc q354 d324 d320 d351 vdd(sw) vdd(sw) 12 13 3 10 11 5 8 stby power amp ic351 27 56o-cd woofer on/off 28 woofer 1/2 lcd401 liquid crystal display 63,64,67-89,94-98 seg0-seg30 59-62 com0-com3 sp191 sp291 sp393 woofer t901 f901 rect d901-904 +6v reg q972 +9v reg q971 cd/radio +6v cd/radio +6v cd +3.3v vdd(sw) vdd(sw) vdd(sw) +9v vdd(sw) vdd(sw) power switch q952,953 +6v reg q954 2 3 +3.3v reg ic902 2 1 reset ic805 com vdd 1 remote control receiver ic891 54 rstx 36 reg chk d406 au 6v buzzer (r-ch) sp292 buzzer (l-ch) sp192 q950,959 pb rec lpf q322 standby switch q352 gain control q323 d321 d322 d952 d951 d462 function switch i-key-0 38 s409,415-417, s419,421 function switch function switch s403,408,410 i-key-3 41 function switch d403-405, d407-411 (illumination) vdd(sw) 3 20 o-pcont det q803 au +6v au +6v d-light+4v 2 3 +4v reg ic901 3 1 +3.3v reg ic806 9 i-rmc(sircs) 45 i-ac/dc-chk dry battery size "d" (iec designation r20) 8pcs, 12v power amp +12v +9v +9v j402 cnp2 audio in j401 mic mix mic level opr/ batt g700cp/g770cp ac in j901 l.in l.ro tape mechanism deck tone surround mcu i/f logic 21 o-p-mute buffer control q403 buffer q405 rv401 r-ch l r-ch r-ch r-ch r-ch j103 sw2 mix amp mix amp q320 amp mic 2 amp mic amp q401,402 d401 q407 q406 vdd(sw) karaoke pon s422 on off g700cp d415 d414 d-light sync out g700cp d801 i-key-wake-up 42 q806 switch i-suffix 48 d802
30 30 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-3. printed wiring board ?bd90 board ? :uses unleaded solder. semiconductor location ref. no. location ic101 e-9 ic201 e-2 ic401 c-10 q301 f-4 see page 27 for circuit boards location. main board cn805 (page 36) optical pick-up block ksm-213cdp a r150 r149 r148 r108 r154 r153 c148 c110 c109 c301 c303 c302 c104 r110 c116 c404 r203 r204 r205 r206 r207 r208 r209 r210 r219 r223 r222 r147 r221 r218 r146 r145 c150 r113 c403 r202 c151 c108 c105 c147 c146 c145 c152 c118 c117 c144 c101 c125 cn201 c143 c120 r144 r157 c142 c141 c140 c100 c107 r408 r156 c124 c127 c126 cn301 r101 c119 c102 r415 r414 c103 r405 c113 r102 r402 r105 r106 c132 c138 c137 r135 r134 r136 r130 r128 r129 r143 r142 r139 c136 r120 r114 c153 c112 r125 r126 c149 c139 r127 r118 r140 r151 c122 c123 r220 r104 b8 b9 b7 s201 r155 c128 c106 c201 r304 r302 c309 c205 c207 c307 r201 r303 c133 r111 r112 c115 r211 q301 r301 c204 c202 c206 c306 r212 c401 c130 x102 c405 bd90 board (side a) bd90 board (side b) 1 3 4 5 ic201 ic401 ic101 e (limit) m401 (spindle) m402 (sled) m m rfi vc tp121 1 a b c d e f g 2 3 4 5 6 7 8 9 10 11 12
31 31 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-4. schematic diagram ?bd90 board ?see page 44 for waveforms. ?see page 44 for ic block diagrams. ?see page 46 for ic pin function description. ic b/d a main board(2/3) cn805 (page 40) 2 1 ic b/d optical pick-up block ksm-213cdp m m vc tp222 r108 r154 r153 c201 r304 r201 r110 r303 tp218 tp216 tp214 tp212 tp210 tp213 tp215 tp217 tp219 tp211 tp209 r203 r204 r205 r206 r207 r208 r209 r210 r219 r223 r222 r221 r218 tp223 r112 tp115 tp114 tp314 tp123 tp205 r202 tp116 r211 tp113 tp112 q301 tp208 tp206 tp207 tp117 tp118 tp119 r301 tp315 c202 tp312 tp107 tp105 tp106 r157 tp122 tp121 tp120 r156 cn301 r101 c401 r415 tp220 r102 tp221 r128 r129 r143 r142 r139 tp111 r114 tp110 s201 r140 tp311 tp309 tp308 tp310 tp109 tp108 tp101 tp102 r151 tp224 r220 tp124 r150 r212 ic101 r105 r106 r125 r126 r127 ic201 x102 tp305 tp304 tp301 tp302 tp303 tp306 tp307 tp313 c301 c307 c309 c100 c138 c153 c151 tp225 tp226 c204 c130 c128 c113 c127 c126 c103 c102 c120 c119 c118 c117 c101 c124 c125 r145 r146 r147 r148 r149 c149 c105 c143 c146 c145 c148 c104 c405 c404 c403 c205 c116 c133 cn201 c110 r113 r111 c115 r155 c109 c132 r104 c123 c122 c139 c150 r136 r135 r134 c112 c108 r120 r118 c136 c107 r130 r144 c144 c147 c140 c137 c141 c142 c106 r302 c306 c303 c302 r405 r402 r408 r414 tp103 tp104 c207 c152 c206 ic401 tp407 tp408 tp409 tp410 0 1m 1m 100 10v 2.2 0 10k 2.2 100 100 100 100 100 100 100 100 100k 100k 100k 100k 100k 100 iop1 0 100 2sa2119k 100k iop2 100 10v apc 100 100 16p 220 220 10v 47k 10k 470k 1k 47k 22k 47k 10k il-sw 0 t- f- f+ t+ fcs trk 0 d1.5v 100k 0 tk63115scl-g@gt 0.1 1 0.001 0.1 470p 0.1 470p 0.1 0.1 0.0022 0.1 0.1 0.1 0.01 0.022 0.01 0.022 0.1 0.0047 0.0047 0 0 0 0 0 22p 0.1 0.01 470p 0.01 47p 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 10k 100 22 6.3v 47 0.1 0.1 0 470p 470p 0.01 0.001 22k 470k 1m 0.1 0.1 47p 0.1 4.7k 22k 0.1 0.1 0.01 0.01 0.0022 0.1 100 10v 0 100 10v 1010 10k 2.2k 2.2k 4.7k sled spdl 1 470p 1 ba5826sfp-e2 sp- sp+ sl+ sl- 100 1m 1k 0 0 0 16.934mhz tc94a70fg-006 5p 5p 21p 0 100k ic101 rf amp, dsp, mp3 ic401 sl/sp/motor driver focus/tracking coil driver ic201 +1.5v reg sp- sp+ sl+ sl- m401 (spindle) m402 (sled) automatic power controller (limit) rfi
32 32 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-5. printed wiring board ?tuner board ? :uses unleaded solder. semiconductor location ref. no. location d1 c-10 d2 d-8 d3 d-8 d10 b-12 d11 b-12 ic1 d-10 ic2 f-4 see page 27 for circuit boards location. ic1 ic2 1-863-438- (11) 11 us,cnd, mx,e92 us,cnd, mx,e92 sp,e41,aus sp,e41,aus r61 r60 r58 r59 c63 r56 r50 c62 c61 r94 c60 c68 c66 r4 r91 c57 r52 c52 c51 c26 c27 r63 r10 r65 c37 r11 c39 d11 d10 r1 c8 r3 c34 c35 d1 c4 c32 r32 r2 c1 c78 c15 c11 c9 c14 c80 c13 r24 r31 c33 r41 c77 r92 c20 c24 c22 c56 c30 d2 c31 r30 r40 c41 c47 c42 c43 r51 r13 c55 r54 c95 r53 c59 r57 r33 r5 r14 r55 jc33 jc34 jc2 jc4 jc3 jc24 jc6 jc5 jc13 jc12 jc11 c7 jc1 jw13 c29 c65 l21 c53 x1 jw3 jw5 c54 jw7 c21 jw9 jw2 c10 t1 jw12 cf4 cf2 jw11 t2 l1 l11 c18 ct1 jw8 c12 l2 c23 jw10 l4 d3 l3 l3 am ferrite bar antenna ct3 c49 jw4 jw6 cnp1 jw14 tp (gnd) tp (cv) main board cn2 c (page 36) ant1 fm telescopic antenna 1 a b c d e f g 2345678910 11 12 13 14
33 33 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-6. schematic diagram ?tuner board ?see page 44 for waveforms. ?see page 45 for ic block diagrams. ic b/d ic b/d 1 c 3 cn2 (page 40) no mark : fm ( ) : am :us, cnd, mx, e92 :sp, e41, aus * sp, e41 aus sp,e41,aus c10 c12 c18 c21 c29 c54 cf4 jc1 jc2 jc3 jc4 jc5 jc6 l4 r2 r3 r4 r10 r24 r32 r41 r51 r58 r59 r60 r61 cf2 r92 r30 r14 r11 jc24 ct3 ct1 x1 c32 c35 c33 c34 c31 c30 c1 c8 c4 c11 c9 c24 c80 c37 c39 c20 c22 c7 c51 c52 c95 c61 c62 c63 c57 c56 l1 d1 l2 d2 r53 r50 c55 r91 c41 c42 ic1 r1 d11 d10 c68 c66 c60 r94 r13 l21 cnp1 ant1 r54 ic2 t2 c49 r40 c43 d3 c23 r5 c53 r55 r52 c59 r63 l3 jc12 jc11 c47 jc13 t1 c65 r65 c27 c26 c15 c14 c13 r31 r33 r56 r57 jc33 jc34 c77 c78 ** us,cnd,mx,e92 us,cnd, mx,e92 0 0 0 0 0 l11 0 0 0 0 0 0
34 34 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-7. printed wiring board ?tc board ? :uses unleaded solder. (11) 11 1-688-389- ic301 c103 r210 r206 r201 r301 r-ch hrp301 record/playback head l-ch yel red wht blk blk (chassis) r104 r103 r202 r203 r204 c104 c203 c204 c201 c205 c105 r305 r101 c101 jc304 r102 c107 c207 r307 c307 r306 c305 r308 c306 r303 jc301 r211 r205 jc303 r309 r304 jc302 r111 r105 r106 r302 r110 jc305 jc306 jc307 jc308 q301 r112 r212 r314 r315 cn303 t301 c102 c302 c202 c301 c304 c303 s301 s301 (rec/pb) rec pb -1-2 he301 erase head tape mechanism deck (1/2) b cn1 (page 36) 1 a b c d e f 2345 6 see page 27 for circuit boards location.
35 35 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-8. schematic diagram ?tc board ?see page 44 for waveforms. ?see page 45 for ic block diagram. ic b/d 2 1 3 cn1 (page 40) no mark : fm ( ) : pb < > : rec [ ] : cd play no mark : fm ( ) : pb < > : rec [ ] : cd play no mark : fm ( ) : pb < > : rec [ ] : cd play no mark : fm ( ) : pb < > : rec [ ] : cd play no mark : fm ( ) : pb < > : rec [ ] : cd play no mark : fm ( ) : pb < > : rec [ ] : cd play r301 c301 r110 r101 c302 c205 r201 r210 r106 r206 r302 r303 r304 r309 c303 c304 r306 r111 r211 r203 r202 r103 r102 r308 c105 c103 c203 c306 c107 c207 c305 t301 c102 r104 r112 c104 r212 r204 c202 c201 c204 ic301 (5,hz) jc302 jc306 jc308 jc305 jc307 jc301 jc303 jc304 r314 r315 q301 r307 c307 r305 c101 r105 r205 cn303 tape mechanism deck (1/2)
36 36 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-9. printed wiring board ?main board ? :uses unleaded solder. see page 27 for circuit boards location. semiconductor location ref. no. location d320 g-10 d321 g-10 d322 h-10 d323 g-11 d324 f-7 d351 h-8 d414 c-4 d415 b-4 d461 b-10 d462 b-11 d801 c-9 d802 d-9 d804 e-8 d805 d-8 d951 g-9 d952 g-9 d953 g-9 d954 h-5 d955 h-7 ic321 f-5 ic351 h-9 ic371 h-4 ic401 b-4 ic801 c-7 ic802 c-9 ic805 c-6 ic806 d-6 ic901 h-7 ic902 g-10 q171 h-4 q271 h-4 q320 f-3 q321 g-7 q322 f-8 q323 f-7 q351 h-10 q352 h-10 q354 g-10 q401 d-3 q402 d-4 q403 d-4 q405 d-4 q406 b-4 q407 b-4 q451 c-6 q452 b-6 q801 c-10 q803 d-9 q804 c-10 q805 c-9 q806 c-9 q812 c-10 q815 c-10 q816 c-10 q950 g-10 q951 g-8 q952 g-8 q953 g-8 q954 g-10 q959 g-10 q971 h-5 q972 h-8 ic401 ic801 ic901 ic371 ic321 ic802 ic806 ic805 ic351 ic902 1 5 10 14 15 20 25 28 15 10 15 ecb ecb 15 10 15 1 1 3 32 45 14 58 1 3 13 45 e e a kk e e e e e e e e e e e a/k ak a kk e s a k a e aa k e e a kk a kk e e e e e e aa k e e 2 1 jr118 jr120 jr133 jr138 jr122 r317 r318 r319 r345 q320 r346 jr105 c962 jr107 r101 jr153 jr134 jr124 r826 q806 jr135 jr155 jr106 r273 r451 r427 r420 c411 r452 q959 q951 r162 q323 q322 q321 q271 q171 q953 q352 d952 d324 d320 d351 d951 d322 d321 d955 d954 r965 r954 r964 r961 r960 r957 r955 r953 r952 r951 r950 r949 r948 r947 r946 r945 r944 r943 r942 r941 r409 c106 c107 c108 c110 c111 c124 c132 r372 r371 r366 r365 r364 r362 r361 r360 r359 r357 r356 r353 r351 c172 c175 c206 c207 c208 r344 c209 c210 c211 r340 r339 c224 c232 c272 c275 r338 r337 r336 r335 c326 c327 c333 c334 c342 c350 c352 c357 r334 c358 r333 c361 c366 r332 c436 c951 c953 c955 r331 r330 r329 r328 r326 r324 r281 r276 r275 r272 r966 r227 r224 r223 r203 r202 r181 r176 r175 r173 r172 r130 r129 r127 r124 r103 r102 r262 r261 q952 fb837 r104 c841 c839 c828 c827 c826 c807 c803 c458 c457 r477 fb834 r161 r363 r485 r488 r490 r325 r491 r492 r803 r804 r805 r809 r810 r825 r834 r835 r836 r837 r838 r839 r840 r841 r842 r843 r844 r845 r846 r847 c846 r848 r849 c831 r850 r851 r852 r853 c820 c819 c815 c813 r854 r855 r342 r343 r856 c456 c455 c454 c453 c451 r857 r348 r858 r859 r860 r861 r862 r863 r864 r865 r866 r867 r868 r872 r875 r877 r879 r880 r881 r882 r883 r235 c459 r453 r454 r456 r461 r462 r463 r493 fb831 r885 r886 r900 r901 r898 r905 r906 r907 q815 q805 q452 q451 q804 q803 q801 fb832 fb835 fb836 d462 d953 d323 r279 r179 r341 d461 q812 cn2 c806 r322 r460 r347 r204 fb833 c302 c437 r126 r226 c109 r252 r152 jr140 r201 r135 r120 r251 r151 r123 jr108 jr152 c304 r220 r153 r154 r253 r254 jr110 jr136 jr111 jr150 jr151 jr113 q403 r429 jr109 r441 r440 r439 r438 r437 r436 r435 r434 r433 r432 r431 r430 c415 c431 c432 c433 q401 q402 q405 r445 r444 r418 r494 r489 r468 r448 c254 c425 c426 d414 q406 q407 r419 d415 r447 cn1 jr114 r446 c430 r470 c154 jr117 jr121 r893 r229 r225 r125 c851 c825 c804 r457 r486 r801 r811 r495 c843 c837 c829 c816 r873 r874 r878 r895 d804 r230 r892 c856 c842 r891 r876 r902 jr128 jr129 jr131 r869 r482 r802 r822 r823 r824 c814 r870 r871 r894 d805 jr126 jr127 r884 r812 r813 r817 r818 r819 c855 c853 r903 r904 r827 r800 r481 r807 r820 r828 r829 r830 c848 c847 c810 r897 r896 r899 d801 r160 r831 c857 r887 r888 jr137 r483 r484 r808 r814 r821 c850 c849 c833 r480 d802 c852 r815 r816 c854 jw101 cnp397 jw102 jw173 jw172 jw177 jw303 jw302 jw304 kh851 jw312 jw313 jw314 jw315 jw291 jw 296 jw 297 jw300 jw299 jw309 jw294 jw292 jw307 jw308 jw298 jw176 jw167 jw169 jw168 jw170 jw180 jw181 jw113 jw112 jw166 jw 162 jw 164 jw161 jw165 jw261 jw185 jw183 jw184 jw182 jw178 jw290 jw279 jw280 jw283 jw287 jw289 jw288 jw286 jw282 jw284 jw 285 jw 264 jw 263 jw 265 jw 266 jw 218 jw 251 jw273 jw271 jw 272 jw269 jw 270 jw216 jw155 jw225 jw 226 jw262 jw217 jw260 jw156 jw157 jw146 jw147 jw144 jw145 jw151 jw153 jw154 jw158 jw149 jw 148 jw103 jw104 c332 jw108 c337 jw109 jw111 jw 135 jw137 jw 139 jw 140 jw134 jw138 jw215 jw 220 jw152 jw150 jw209 jw 212 jw211 jw213 jw200 jw 219 jw 227 jw 240 jw221 jw222 jw252 jw239 jw229 jw 242 jw257 jw 230 jw 160 jw 223 jw 244 jw243 jw246 jw 228 jw 241 jw259 jw248 jw250 jw224 jw247 jw 256 jw204 jw206 jw 232 jw 234 jw233 jw207 jw 202 jw 199 jw192 jw194 jw193 jw196 jw 197 jw198 c381 jw129 jw127 jw 320 jw186 jw188 jw189 jw 190 jw195 jw187 jw116 jw117 jw125 jw130 jw 123 jw124 jw131 jw 122 jw 126 jw132 c344 jw107 jw205 jw 118 jw120 jw136 jw141 jw121 jw119 jw245 jw275 jw276 jw255 jw208 jw128 jw253 jw254 jw133 jw210 jw231 jw142 jw171 cn803 c402 c362 q354 cnp805 c349 cnp807 c121 c123 c305 c131 c127 c173 c223 c226 c231 q954 q950 q351 q972 q971 c271 c273 c301 c335 c336 cnp303 cnp391 cnp301 cnp393 c338 cnp394 c339 c340 c341 c343 c345 c348 c346 c274 c174 c351 c353 c303 c961 c957 c954 c354 c355 c356 c359 c125 c360 c371 c380 c152 c153 c225 c252 c253 c424 c423 c422 c421 c420 c419 c427 c417 c416 c418 c251 c221 c151 l804 c808 c805 c461 q816 c261 l159 l158 cnp803 cnp806 c161 cn805 cnp390 cn804 l803 l160 c126 c347 x802 c227 c171 tp1 g770cpk g770cpk g770cpk g700cp us,sp,e41 g770cpk g700cp g770cpk g770cpk g770cpk us,sp,e41 g770cpk g770cpk sp,e41,aus us,cnd, mx,e92 e i j h lcd board cn801 (page 38) d led1 board hk402 (page 38) f lcd board cn802 (page 38) power key board kh407 (page 38) volume key board kh405 (page 38) cd keyboard kh406 (page 38) n microphone board kh354 (page 37) b tc board cn303 (page 34) g power board kh903 (page 42) s971 play sp393 (woofer) s972 motor m971 capstan/ reel motor m d-light board kh356 (page 37) l headphone board kh353 (page 37) k audio in board kh355 (page 37) a bd90 board cn201 (page 30) c tuner board cnp1 (page 32) m push open/close sw2 tape mechanism deck (2/2) 12 a b c d e f g h 34567891 0 11
37 37 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-10. printed wiring boards ?audio section ? :uses unleaded solder. see page 27 for circuit boards location. 3 1 3 4 1 2 5 3 1 61 51 l302 l306 l307 j103 kh356 jr205 jr206 r121 r122 r221 r222 kh355 l102 cnp357 l101 l202 j402 audio in r465 r473 r464 r426 c408 c414 kh354 rv401 s422 d401 l303 l304 l305 l308 r192 r193 r194 r292 r293 r294 kh353 jw405 jw406 j391 cnp392 l301 audio in j401 mic mix mic level karaoke pon karaoke pon m main board cnp397 (page 36) k main board cnp394 (page 36) d-light sync out g700cp g770cpk 3 1 cnp2 on off n main board cnp390 (page 36) l main board cnp391 (page 36) sp292 (buzzer) sp291 (rch) sp192 (buzzer) sp191 (lch) 12 a b c d e 3456
38 38 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-11. printed wiring boards ?control section ? :uses unleaded solder. see page 27 for circuit boards location. ic891 12 12 1 3 1 1 2 2 2 1 1 2 2 1 1 2 1 2 1 1 2 3 r443 r425 r415 r414 r413 r412 r411 r458 kh405 s411 s412 s404 s418 s420 s407 r400 r455 r408 r399 kh407 s408 s403 s410 r403 r402 r401 r424 r423 r417 r416 r459 s409 s421 s415 s419 s417 s416 cnp401 r404 r422 r421 r410 r407 r406 r405 r466 kh408 kh406 s406 s405 s414 s413 s402 s401 cn802 r475 r469 r428 c401 cn801 d406 lcd401 (liquid crystal display) r472 r471 hk402 cnj403 d404 d 403 r450 r449 cnj404 cnj405 d 408 d405 r487 r476 cnj406 cnj407 d 411 d407 r479 r478 d410,d409 (illumination) d407,d411 (illumination) d405,d408 (illumination) d403,d404 (illumination) cnj408 d 410 d409 i main board cnp803 (page 36) auto preset radio/band audio in sleep dspl/ent power power drive woofer reggaeton flat rock dance salsa mode repeat vol vol opr/ batt e main board cn804 (page 36) f main board cn803 (page 36) d main board cnp807 (page 36) j main board cnp806 (page 36) h main board cnp805 (page 36) 12 a b c d e f 345678 semiconductor location ref. no. location d403 d-4 d404 d-4 d405 d-3 d406 c-3 d407 d-2 d408 d-3 d409 d-1 d410 d-1 d411 d-2 ic891 c-1
39 39 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-12. schematic diagram ?main (1/3), audio section ?see page 44 for ic block diagram. 40 43 41 * 1 1 1 1 1 1 5 6 3 5 4 3 1 1 1 1 6 3 5 3 1 3 1 3 1 4 t ape mechanism deck (2/2) q354 ic351 ic371 q971 q972 c107 c106 c108 c109 c207 c206 c208 c209 kh355 kh353 cnp303 cnp394 c210 c211 d954 d955 q351 r102 r103 r181 r193 r194 r202 r203 r281 r293 r294 r324 r328 r329 r330 r332 r333 r334 r335 r336 r337 r339 r351 r353 r357 r359 r360 r361 r371 r372 r941 r942 r943 r944 r949 r950 r951 r952 r953 r961 r964 c121 c221 r230 r130 j391 d351 r954 ic902 r279 r179 q954 j402 r347 r945 r946 r 947 r948 r104 r204 r965 r966 cnp357 ic321 l102 l202 l301 r122 r960 c347 c226 c126 r123 r124 r224 r120 r220 r225 r348 r957 kh354 r464 r465 r473 l101 l303 l304 r175 r275 r176 r276 r362 sp393 l308 r252 r363 cnp390 r135 r235 c224 r126 r226 c337 r317 r319 c344 r345 c332 d324 q321 c342 c326 c327 d320 d322 q171 q271 q352 q950 c955 c953 d323 d953 q959 c350 c951 q953 d951 q951 q952 c275 c175 c361 c357 c358 c437 kh356 cnp397 c381 c962 ic901 r341 r127 r227 c131 c231 c335 r344 r331 c132 c111 c110 c302 c303 c304 c305 c232 c124 c123 r151 r152 r229 r223 c223 r251 r318 c340 r338 c334 c333 c339 c341 c336 r340 q322 c301 c355 c356 c359 r364 r365 c360 c354 c353 c338 d321 c366 r325 r322 c352 c351 r356 r326 c173 c273 c274 c174 c346 c371 c271 c127 c227 r172 r272 c272 c172 c171 r273 r173 q320 r366 c225 c125 r342 r343 c349 c380 c345 c362 c961 r955 c957 d952 cnp301 c348 c954 r121 r221 r222 cnp2 r192 r292 j103 cnp391 l302 l306 l307 s422 d401 c414 cnp392 l305 c343 c436 r129 r125 r346 q323 j401 c408 r426 rv401 cnp393 sp191 sp192 sp291 sp292 lch 3.2 ohm rch 3.2 ohm c430 ba5417 ba5417 ktc3203y-at ktd2058y ktd2058y 0.1 0.1 0.047 0.047 0.1 0.1 0.047 0.047 3p 5p 6p 6 1 3p 0.0047 0.0022 udzste-1710b udzste-176.8b ktc3198gr-at 10k 47k 4.7 220 220 10k47k 4.7 220 220 2.2k 1k 2.2k 470 470k 10k 470 22k 10k 22k 1k 4.7k 4.7k 470 10 10 2.2k 10k 10k 2.2k 2.2k 2.2k 2.2k 2.2k 2.2k 100k 2.2k 2.2k 1k 100 1 50v 1 50v 47k 47k hp jack mc2837 100k ta78033ls 4.7k 4.7k ktc3203y-at audio in jack 470k 2.2k 2.2k 2.2k 2.2k 4.7k 4.7k 10 10 3p r2s15904sp 22k 470 10 50v 2.2 50v 2.2 50v 4.7k 0 0 4.7k 4.7k 22k 4.7k 0 220 220 22 22 470 woofer 4 ohm 220 00 100p mc2838-t112-1 2sc3052ef -t1-lef 100p 0.047 0.022 m c2838-t112-1 1ss355wte-17 2sc3052ef -t1-lef 2sc3052ef -t1-lef rt1p436c-tp-1 kta1271y-at 0.022 0.022 1ss355wte-17 1ss355w te-17 rt1n144c-tp-1 0.022 0.022 rt1n431c-tp-1 1ss355w te-17 rt1n237c-tp-1 0.1 0.1 0.01 0.1 0.1 1 4.7k 10k10k 0.47 50v 0.47 50v 1 50v 4.7k 22k 100p 0.0022 0.0047 1 10 50v 0.1 470 16v 100p 2.2 50v 0 4.7k 2.2 50v 100 10v 2.2k 0.022 0.01 100 10v 22 25v 220 10v 1k 2sc3052ef-t1-lef 100 10v 100 10v 22 25v 1m 1m 2.2 50v 100 10v 100 10v 10 50v 1ss355wte-17 100p 2.2k 0 0.1 100 10v 1k 1k 100 10v 100 10v 1000 10v 1000 10v 1000 25v 100 10v 47 10v 1 50v 1 50v 10k 10k 470p 470p 47 10v 2.2k 2.2k 10k 4.7 50v 4.7 50v 2.2k 2.2k 220 25v 220 10v 10 50v 10 50v 220 10v 0 220 10v mc2836-t112-1 5p 6800 25v 220 16v 22k 22k 22k 3p 1k 1k 5p 0 0 0 4p 10 50v 0.1 0 22k 2sk2158-t2b 4p 1 6p 6p 4.7k 2.2k 2.2k 4.7k 47k 47k 1 50v 10k 4.7k 10 50v 470 1 50v 2sa1235f 3p 3p 100 10v 0.022 tk70540scl-g 100p * 4.7k * 470k 220 2sc3052ef-t1-lef 5p l-34hd 4700p 47 0.047 1k 10k 10v
40 40 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-13. schematic diagram ?main section (2/3) ?see page 44 for waveform. ?see page 45 for ic block diagram. ?see page 49 for ic pin function description. 33 35 39 31 41 41 41 41 41 41 41 * * * 1 2 1 2 1 2 1 2 1 3 c808 d 46 2 r480 r481 r493 r802 r 8 1 1 r 8 1 2 r 8 1 3 r820 r821 r822 r828 r829 r830 r 8 3 5 r 8 3 6 r 8 3 7 r 8 3 8 r 8 4 8 r 8 4 9 r 8 5 0 r 8 5 1 r 8 5 2 r 8 5 3 r 8 5 4 r868 r870 r 8 7 6 ic806 r468 r 4 5 7 r 8 2 5 r814 r 4 8 8 r461 r462 r456 r448 r 8 6 4 r 8 6 5 r 8 4 7 r808 r807 r 8 4 6 r 8 4 5 r 8 4 4 r 8 4 3 r 8 4 2 r 8 4 1 r 8 4 0 r 8 3 4 l804 r858 r859 r857 r855 r856 r860 r861 r862 r863 r866 r867 r879 r881 r882 r883 r484 r 8 7 4 r 8 0 3 r 8 7 5 r 8 0 4 r 8 7 7 r 8 7 2 r 8 8 0 r 8 7 3 r824 r 8 7 8 r839 r871 r897 r899 q816 r 8 1 9 r 8 1 8 r 8 1 7 r 8 0 5 r 8 1 0 r 9 0 2 r815 r816 r 8 0 9 r 9 0 3 r 9 0 4 r 9 0 5 r 9 0 6 r823 r482 r 4 9 1 r826 r827 cnp806 cnp805 r 8 0 1 r460 r463 cnp807 ic801 r485 cnp803 x802 ic 8 0 2 r162 f b 8 3 5 f b 8 3 6 r888 r154 r 2 5 3 r254 1 r 4 9 0 r 4 9 2 r831 r869 r 8 8 4 r887 q805 cn1 c826 q812 cn805 f b 8 3 4 f b 8 3 1 f b 8 3 3 f b 8 3 7 c806 c825 ic805 c457 c456 c458 c 8 1 3 c 8 5 5 c 8 5 4 c 8 4 2 c 8 5 6 d805 c810 c 8 5 7 c 8 5 2 q803 cn803 c847 c848 c849 c850 c833 d 8 0 1 d 8 0 2 c820 cn804 kh851 d461 c 8 1 5 l158 l160 c819 c451 c453 c459 c455 r454 c454 r453 q451 q452 c 8 4 6 c 8 3 1 l 1 5 9 c807 l803 r886 r885 c805 c804 c803 c853 c843 r 8 9 5 c 8 5 1 c 8 3 7 c 8 1 6 c829 r486 r495 r477 c151 r153 c251 r900 r901 c841 c839 c828 c827 r262 r161 c161 c261 r261 fb832 c 8 1 4 r 9 0 7 r894 r896 r420 r409 r451 r427 r452 r160 r892 r891 r800 q801 q804 q815 r483 c411 c461 q806 r893 d 8 0 4 r101 r201 r898 cn2 sw2 100 10v u d z s t e- 1 7 5 .1 b 47k 47k 1k 1k 1 0 k 1 k 1 k 470k 1k 1k 4.7k 4.7k 4.7k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 470 1k 2 2 0 xc6202p332fr 1k 1 0 k 1 k 1k 2 2 k 470 470 1k 1k 1 k 1 k 1 0 k 1k 4.7k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k 1 0 k jw 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 1k 47k 1 k 1 k 1 k 1 k 1 k 1 k 1 k 1 k 1k 1 k 47k 470 100 100 kta1271y-at 1 k 1 k 1 k 1 k 4 .7 k 1 k 1k 1k 1 k 1 k 1 k 1 k 1 k 1k 1k 0 2p 3p 4 7 0 220 220 2p mb90802npf -g-127e1 47k 2p 5.53mhz s - 2 4 c s 0 2 a f j -t b -g 47k f b f b 0 0 11p 0.001 rt1n144c-tp-1 21p 0 0 0 0 11 s-80828cnmc -b8nt2g 0.01 22p 0.01 0 .1 1 0 0 p 1 0 0 p 1 0 0 p 1 0 0 p 1ss355wte-17 0.01 1 0 0 p 1 0 0 p 2sc3052ef -t1-lef 19p 0.01 0.01 0.01 0.01 100p m c 2 8 3 6 -t 1 1 2 -1 m c2 8 3 6- t1 1 2 -1 0.1 19p 2p mc2838-t112-1 0 .1 0.1 8p 22p 10p 47p 10k 47p 1k 2sc3052ef -t1-lef 2sc3052ef -t1-lef 1 0 0 p 1 0 0 p 0.01 47k 1k 100 10v 0.01 0.1 100p 100p 1 0 0 p 1 0 0 p 1 0 0 p 100k 100k 100k 47k 47k 100p 220p 1000p 4700p 0 1k 1 1 50v 1k 0 0 .1 1 0 k 10 10k 4.7k 1k1k 1k1k 47k 0 47k 2.2k rt1n144c -tp-1 rt1n144c-tp-1 rt1p144c-tp-1 47k 100p 10 50v 11p * * * 10k 4 .7 k 10k 1k 1k 4 7 0 47k isa1235ac1tp-1ef 1 0 100p 10 50v 4.7k 10 50v rt1n436c-tp-1 0 1 s s 3 5 5 w t e -1 7 00 4.7k 21
41 41 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-14. schematic diagram ?main (3/3), control section 40 40 40 40 40 40 40 39 * cnj403 cnj404 cnj405 cnj406 cnj407 cnj408 ic891 r404 r405 r406 r407 r412 r411 r413 r414 r415 r410 r421 r422 r425 r403 r401 r402 r423 r424 r400 r399 r408 r443 r416 r417 r475 kh407 kh408 kh406 kh405 r455 r458 r459 r466 cnp401 c152 c153 c252 c253 c402 c415 c416 c417 c418 c419 c420 c422 c423 c427 ic401 q403 q406 q407 r418 r419 r430 r431 r432 r433 r434 r435 r436 r437 r438 r440 r441 r444 r445 r446 r447 r489 r494 cn801 cn802 hk402 r469 c401 r428 d406 lcd401 s408 s410 s403 r471 r472 d403 d404 d405 d408 d407 d411 d409 d410 r449 r450 r476 r487 r478 r479 s411 s412 s404 s418 s420 s407 s409 s415 s416 s421 s417 s419 s401 s402 s414 s405 s406 s413 c425 c426 c254 c154 c433 c431 d414 d415 q402 q401 r470 c424 c421 q405 r439 r429 c432 2p 2p 2p 2p 2p 2p rpm7140-v4 1k 2.2k 1k 2.2k 470 220 1k 1k 2.2k 220 470 1k 2.2k 1k 220 470 1k 2.2k 220 470 1k 1k 2.2k 1k 220k 2p 2p 3p 2p 100 100 100 100 2p 19p 19p 2p 100k 1 220 l-34hd switch switch switch 220 220 il4345v22d0tdt02 il4345v22d0tdt02 il4345v22d0tdt02 il4345v22d0tdt02 il4345v22d0tdt02 il4345v22d0tdt02 il4345v22d0tdt02 il4345v22d0tdt02 220 220 220 220 220 220 switch switch switch switch switch switch switch switch switch switch switch switch switch switch switch switch switch switch * 50v * 50v 10v 50v 50v 50v 10v 10v 22 25v 50v ba3837 rt1n144c-tp-1 rt1n144c-tp-1 rt1n144c-tp-1 1k 47k 47k 470 1k 47k 1k 4.7k 2.2k 1k 1k 470 220k 100k 4.7k 470 47k 47k 47k 50v 220p 220p 100p 100p 1ss355wte-17 mc2836-t112-1 2sc3052ef -t1-lef 2sc3052ef -t1-lef 470 50v 50v 2sc3052ef -t1-lef 470 2.2k 100p ?see page 44 for ic block diagram.
42 42 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-15. printed wiring boards ?power section ? :uses unleaded solder. see page 27 for circuit boards location. semiconductor location ref. no. location d901 c-7 d902 c-6 d903 c-7 d904 c-6 5 1 4 1 c928 c901 c902 c903 c904 c927 kh902 kh903 jw274 jw402 fh902 j901 ~ac in f902 fh901 built in transformer not replaceable: * * t901 power transformer d901 d902 d903 d904 c909 jw942 jw941 cnp941 jw944 jw943 g main board cnp301 (page 36) dry battery size "d" (iec designation r20) 8pcs,12v 12 a b c d e f 345678
43 43 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk 7-16. schematic diagram ?power section 39 * 4 1 4 1 fh901 fh902 jw941 jw942 jw943 jw944 f902 * kh902 cnp941 kh903 t901 j901 c928 c927 c909 d904 d903 c904 c903 c902 d902 d901 c901 holder fuse holder fuse jw jw jw jw fuss glass tube 4p 4p 5p 1 1 2200 25v 1n5401-c352 1n5401-c352 0.022 0.022 0.022 1n5401-c352 1n5401-c352 0.022 power transformer
44 44 CFD-G700CP/g770cp/g770cpk CFD-G700CP/g770cp/g770cpk ?a veforms ?bd90 board ?tc board ?tuner board ?main board 1 ic2 w; (xout) 13.3 s 1.5 vp-p 500 mv/div, 5 s/div 1 q301 c (rec) 19.5 sec 19.5 sec 4 vp-p 1 v/div, 5 s/div 2 t301, hrp301 (yel) 40 vp-p 10 v/div, 5 s/div 1 ic801 os (x1) 3.4 vp-p 180 ns 1 v/div, 100 ns/div 1 ic101 ia (rfi) (cd play mode) 1.3 vp-p 200 mv/div, 500 ns/div 2 ic101 wf (xo) (cd play mode) 59.1 ns 3.3 vp-p 1 v/div, 20 ns/div ? ic block diagrams ic201 tk63115scl-g@gt ?bd90 board vin 1 gnd 2 vout 3 v ref on/off control thermal & over current protection vcont 5 4nc 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 24 23 22 21 20 19 18 17 16 15 25 level shift level shift level shift level shift gnd in4 in4' bias vcc vcc in3' in3 vol(+) vol(-) reset opin vo1(-) regb vo1(+) in1 reset regout mute gnd in2' in2 vo2(+) vol(-) gnd opout mute vcc vcc 13.3k 13.3k 13.3k 13.3k 100 10k 10k 10k t. s.d. regulator,bias drop vo3(-) vo3(+) ch3 ch4 ch2 ch1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 24 23 22 21 20 19 18 17 16 15 25 vcc inl3 inl4 agnd dgnd refin inl1 inr1 inr2 inr3 inr4 inl2 trel trer bassl2 bassl1 bassr1 bassr2 lout rout nc nc clk data tone control bass/treble surround input gain control igoutr igoutl volinr volinl mute mute input gain control l ch tone control bass/treble r ch mcu i/f 0 - +12db/2db step 0 - +12db /2db step volume volume 0 - -89db. 0 - -89db. ref input selector input selector selector mode ic401 ba5826sfp-e2 ic321 r2s15904sp ?main board logic sw2 1 3 12 16 lout v cc 7bias 8 gnd 4fk sw1 l l-r r l+r 5 tk 2 mic 6lin 9rin lp 11 lp c 15 b 14 a 13 rout 10 lp ic401 ba3837
45 CFD-G700CP/g770cp/g770cpk ic805 s-80828cnmc-b8nt2g ?main board vref 4 5 1 2 nc nc out v dd 3v ss ic1 ta2149bn ?tuner board ic2 lc72137m-tlm-e gnd1 3 2 1 if req am mix fm rf-in am low cut 5 4 mix out vcc2 af if-in 8 7 6 fm if-in gnd2 10 9 agc quad 12 11 r-out l-out fm rf-out 22 23 24 20 21 17 18 19 15 16 13 14 am rf-in vcc1 fm osc st-ind osc-out am osc if-out lpf2/mo-st mpx- in det-out lpf1/band fm mix fm osc level det am det mute fm det st/mo fm/am am osc agc sw st 1/8 buff buff divide decode vco if buff af buff af fm rf am if fm if 1/1 or 1/16 11 10 9 8 7 6 5 4 3 2 1 12 13 14 15 16 19 20 unlock detector power on reset universal counter ccb i/f ce di cl do xout lp-out xin lp-in pd vss vdd mo/st fm in am in mute fm/am band st-ind band if in phase detector charge pump reference divider swallow counter 1/16,1/17 4bits 12bits programmable divider data shift register latch 1/2 17 18 1 2 3 6 9 10 11 12 8 7 4 5 22 tape tape tape buf amp a1 buf amp a2 nab amp1 nab amp2 23 24 15 14 13 21 20 17 16 radio buf amp b1 buf amp b2 mute mute on on on 7db 26db 26db monitor amp logic 18 19 mute 7db monitor amp line tape radio line alc2 alc1 det rec amp1 rec amp2 2.1 ref amp mic amp1 vcc r.lo line r.rad tape r.lin mic l.lo rec l.rad mic i/ex l.lin agc l.po l.nf l.ro l.in ref gnd r.in r.ro r.nf r.po mic.nf ic301 ta2068n (5, hz) ?tc board
46 CFD-G700CP/g770cp/g770cpk ic pin function description bd90 board ic101 tc94a70fg-006 (rf amp, dsp, mp3) pin no. pin name i/o description 1a vss3 ground terminal (used cd analog 3.3v) 2 rfzi i rf ripple zero cross signal input terminal 3 rfrp o rf ripple signal output terminal (used zero cross) 4sb ad/rfdc o not used (open) 5 fei o not used (open) 6 tei o tracking error signal output terminal (not used (open)) 7 tezi i tracking error signal input terminal (used zero cross) 8a vdd3 power supply terminal (used cd analog 3.3v) 9f oo o focus servo equalizer output terminal 10 tro o tracking servo equalizer output terminal 11 vref ref of analog power supply terminal 12 fmo o feed servo equalizer output terminal 13 dmo o disc servo equalizer output terminal 14 vssp3 ground terminal (used dsp voc 3.3v) 15 vcoi o pd output terminal (used vco) 16 vddp3 power supply terminal (used dsp vco 3.3v) 17 vdd1 power supply terminal (used digital 1.5v) 18 vss1 ground terminal (used digital 1.5v) 19 fgin i fg signal input terminal (used cav) (not used (fixed to ??) 20 io0(/hso) i play speed mode flag input terminal 21 io1(/uhso) i not used (open) 22 xvss3 ground terminal (used system clock 3.3v) 23 xi i system clock input terminal (16.934mhz) 24 xo o system clock output terminal (16.934mhz) 25 xvdd3 power supply terminal (used system clock 3.3v) 26 dvss3 ground terminal (used dac) 27 ro o audio r-ch data output terminal 28 dvdd3 power supply terminal (used dac 3.3v) 29 dvr ref voltage terminal (used dac) 30 lo o audio l-ch data output terminal 31 dvss3 ground terminal (used dac 3.3v) 32 vddt3 power supply terminal (used digital i/o 3.3v) 33 vss1 ground terminal (used digital 3.3v) 34 vdd1 power supply terminal (used digital 1.5v) 35 vddm1 power supply terminal (used 1m bit sram 1.5v) 36 sramstb i 1m bit sram standby input terminal (not used (fixed to ??) 37 rst i reset signal input terminal 38 bus0 i data input terminal (bus line) 39 bus1 i data input terminal (bus line) 40 bus2(so) i data input terminal (serial output) 41 bus3(si) i data input terminal (serial input) 42 buck(clk) i bus clock input terminal (serial clock input) 43 cce i clip enable input terminal (u-com interface) 44 test i test setting terminal (not used (fixed to ??) 45 irq i cut in dsp input terminal (not used (fixed to ??) 46 aout3(po4) o not used (open) 47 aout2(po5) o not used (open)
47 CFD-G700CP/g770cp/g770cpk pin no. pin name i/o description 48 pio0 o req output terminal 49 pio1 i not used (open) 50 pio2 i not used (open) 51 pio3 i not used (open) 52 vss1 ground terminal (digital 3.3v) 53 vddt3 power supply terminal (digital i/o 3.3v) 54 sbsy o sub code block sync output terminal 55 sbok/fok o not used (open) 56 ipf o not used (open) 57 sfsy/lock o not used (open) 58 zdet o dac zero data detect flag output terminal (not used (open)) 59 gpin i general purpose input terminal (not used (fixed to ??) 60 ms i u-com i/f mode select input terminal (fixed to ?? 61 dout(po6) o not used (open) 62 aout1(po7) o not used (open) 63 bck(po8) o not used (open) 64 lrck(po9) o not used (open) 65 ain(pi4) i data input terminal (used dac) (not used (fixed to ??) 66 bcki(pi5) i bit clock input terminal (used dac) (not used (fixed to ??) 67 lrcki(pi6) i channel clock input terminal (used dac) (not used (fixed to ??) 68 vdd1 power supply terminal (digital 1.5v) 69 vss1 ground terminal (digital 1.5v) 70 awrc o not used (open) 71 pvdd3 power supply terminal (pll 3.3v) 72 pdo o phase error signal of efm signal and plck signal output terminal 73 tmaxs o not used (open) 74 tmax o output terminal of tmax detect signal 75 lpfn i reverse input terminal of amp (pll-lpf) 76 lpfo o output terminal of amp (pll-lpf) 77 pvref 1.65v ref power terminal (only pll) 78 vcof o vco filter output terminal 79 pvss3 ground terminal (pll 3.3v) 80 slco o efm slice level output terminal 81 rfi i rf signal input terminal 82 rfrpi i rf ripple signal input terminal 83 rfeqo o rf equalizer output terminal 84 vro o 1.65v ref voltage output terminal 85 resin o ref resister terminal (22k/0.01u) 86 vmdir ref voltage of apc circuit output terminal 87 testr o lpf terminal (rfeqo offset correct) 88 agci i rf signal adjustment amp input terminal 89 rfo o rf signal amp output terminal 90 rvdd3 3.3v power supply terminal (rf amp) 91 ldo o laser diode amp output terminal 92 mdi i monitor photo diode amp input terminal 93 rvss3 ground terminal (rf amp 3.3v) 94 fni2(c) i main beam input terminal (connect to pin diode c) 95 fni1(a) i main beam input terminal (connect to pin diode a) 96 fpi2(d) i main beam input terminal (connect to pin diode d)
48 CFD-G700CP/g770cp/g770cpk pin no. pin name i/o description 97 fpi1(b) i main beam input terminal (connect to pin diode b) 98 tpi(f) i sub beam amp input terminal (connect to pin diode f) 99 tnpc o capacitor connect terminal to the middle pointof tni/tpi input register 100 tni(e) i sub beam amp input terminal (connect to pin diode e)
49 CFD-G700CP/g770cp/g770cpk main board ic801 mb90802npf-g-127e1 (system controller) pin no. pin name i/o description 1 clk-shift_am o clock shift signal output for am radio 2 clk-shift_fm o clock shift signal output for fm radio 3 i-mp3-req i request signal input from cd-dsp-mp3 decorder (ic101) 4 o-mp3-m-mute o mute signal output to spindle and sleding motor driver (ic401) i/o-mp3-bus0 5 to 8 i/o-mp3-bus1 i/o two-way data bus for cd-dsp-mp3 decorder (ic101) i/o-mp3-bus2(so) i/o-mp3-bus3(si) 9 i-rmc (srcs) i sircs remote control signal input 10 lid-open i cd lid open detect signal input 11 tape play i tape play detect signal input 12 tape rec i tape rec detect signal input 13 nc(gnd) not used (fixed to ?? 14 nc(open) not used (open) 15 vcc power supply terminal (+3.3v) 16 vss ground terminal 17 o-mp3-buck(clk) o bus clock signal output to cd-dsp-mp3 decorder (ic101) 18 o-mp3-ccen o chip enable signal output to cd-dsp-mp3 decorder (ic101) 19 o-mp3-xrst o reset signal output to cd-dsp-mp3 decorder (ic101) 20 o-pcont o power control signal output (h:on) 21 o-p-mute o mute signal output to power amplifier 22 o-tu-ce o chip enable signal output to tuner pll (ic2) 23 i-tu-do i serial data input from tuner pll (ic2) 24 o-tu-clk o serial clock signal output to tuner pll (ic2) 25 o-tu-di o serial data output to tuner pll (ic2) 26 o-tu-mute o mute signal output to tuner pll (ic2) 27 woofer_on/off o woofer control signal output (h:on/l:off) 28 woofer_1/2 o woofer level control signal output (h:level-2, l:level-1) 29 woofer_led1 o woofer led control signal output (h:level-1) 30 woofer_led2 o woofer led control signal output (h:level-2) 31 o-a-mute o mute signal output 32 avcc power supply terminal (+3.3v) 33 o-vol-data o serial data output to evr (ic321) 34 o-vol-clk o serial clock output to evr (ic321) 35 avss ground terminal 36 i-reg6v-chk i 6v regulator check input 37 i-mic-in i mic input detect (h:detect) 38 to 41 i-key0-3 i key input 42 i-key-wake-up i key wake-up input 43 i-mp3-sbsy i sub code block sync input terminal 44 vss ground terminal 45 i-ac/dc-chk i ac/dc detect (l:ac) 46 o-buf-cont o mic buffer control signal output 47 nc not used (open) 48 i-suffix i suffix control input 49 eeprom-sda i/o serial data input/output to eeprom (ic802) 50 eeprom-sck o serial clock output to eeprom (ic802) 51 to 53 md2-0 i flash mask (fixed to md2:l, md1:h, md0:h)
50 CFD-G700CP/g770cp/g770cpk pin no. pin name i/o description 54 rstx i system reset signal input 55 o-cd-sw o pre-amp select signal output 56 o-cd o cd+3.3v regulator control signal output 57 o-tape o pre-amp select signal output 58 vlcd i lcd power setting input 59 to 62 com1-4 o common signal output to the lcd 63, 64 seg1,2 o segment signal output to the lcd 65 vcc power supply terminal (+3.3v) 66 vss ground terminal 67 to 89 seg3-25 o segment signal output to the lcd 90 vcc power supply terminal (+3.3v) 91 vss ground terminal 92 x1 o main clock output terminal (4.19mhz) 93 x0 i main clock input terminal (4.19mhz) 94 to 98 seg26-30 o segment signal output to the lcd 99 nc not used (open) 100 nc not used (open)
51 CFD-G700CP/g770cp/g770cpk section 8 exploded views note: -xx and -x mean standardized parts, so they may have some difference from the original one. items marked ??are not stocked since they are seldom required for routine service. some delay should be anticipated when ordering these items. the mechanical parts with no reference number in the exploded views are not supplied. ? bb re viation au s: australian model cnd : canadian model e41 : ac 230v area in e model e92 : ac 120v area in e model mx : mexican model sp : singapore model ref. no. part no. description remark ref. no. part no. description remark 1 2-895-570-01 lid, cord case 2 2-895-569-01 case, cord 3 a-1244-296-a audio in board, complete 4 3-252-827-01 screw (b2.6), (+) bv tapping 5 3-252-828-01 screw (b2.6), (+) pwh tapping 6 3-254-143-11 screw (b3), (+) bv tapping 7 2-895-573-01 lid, battery 8 3-254-145-11 screw (b3), (+) bv tapping 9 2-895-574-01 handle cnp2 1-833-922-11 cord, connection (with plug) sp191 1-826-684-11 speaker (10cm) sp291 1-826-684-11 speaker (10cm) 8-1. overall section the components identified by mark 0 or dotted line with mark 0 are critical for safety. replace only with part number specified. les composants identifi?s par une marque 0 sont critiques pour la s?curit?. ne les remplacer que par une pi?ce portant le num?ro sp?cifi?. sp291 cnp2 sp191 cabinet (front) section 7 3 4 1 2 8 8 8 9 cabinet (rear) section cabinet (upper) section 5 6 6 8
52 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark 51 x-2177-000-1 panel, (front) sub assy 52 2-895-583-01 cover, panel 53 a-1244-292-a lcd board, complete 54 3-254-151-01 screw (b2.6), (+) p tapping 55 3-254-143-11 screw (b3), (+) bv tapping 56 3-254-140-01 screw (b2.6), (+) bv tapping 57 2-895-575-01 ring, ornamental 58 2-895-579-01 holder, ring 59 2-895-576-01 ring, light guide 60 x-2177-001-1 cabinet, (front) sub assy (g770cpk) 60 x-2177-002-1 cabinet, (front) sub assy (g700cp) 60 x-2177-003-1 cabinet, (front) sub assy (g770cp) 61 3-198-121-01 sheet (wire), adhesive 62 a-1244-297-a headphone board, complete 63 3-252-830-01 screw (b3), (+) pwh tapping 64 2-895-584-01 button, power 65 3-252-827-01 screw (b2.6), (+) bv tappingng 66 3-252-828-01 screw (b2.6), (+) pwh tapping 67 a-1244-294-a power key board, complete 68 2-657-081-02 knob, micvolum (g770cpk) 69 2-895-594-01 cap, switch (g770cpk) 70 a-1244-295-a microphone board, complete (g770cpk) 71 2-895-585-01 button, tune 72 a-1244-293-a volume key board, complete 73 a-1243-618-a led1 board, complete 74 a-1243-619-a led2 board, complete 75 a-1243-620-a led3 board, complete 76 a-1243-621-a led4 board, complete 77 3-831-441-11 cushion (b) d403 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d404 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d405 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d407 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d408 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d409 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d410 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d411 6-501-452-01 diode 1l4345v22dotdt02 (illumination) sp393 1-826-683-11 speaker (13cm) 8-2. cabinet (front) section 51 70 52 53 62 68 69 64 67 77 54 55 66 63 65 55 65 65 65 66 72 77 60 71 g770cpk 73 sp393 d404 d405 d407 d411 d408 d403 74 75 76 d410 d409 57 55 56 59 not supplied not supplied 61 58
53 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark 8-3. cabinet (rear) section 101 3-254-143-11 screw (b3), (+) bv tapping 102 2-895-581-01 holder, transformer (g770cp/g770cpk) 102 2-895-581-11 holder, transformer (g700cp) 103 a-1243-633-a power board, complete (us, cnd, mx, e92) 103 a-1244-369-a power board, complete (sp, e41, aus) 104 2-895-596-01 bracket (transformer) 105 2-895-565-01 cabinet (rear) (mx) 105 2-895-565-11 cabinet (rear) (g700cp) 105 2-895-565-21 cabinet (rear) (cnd, e92) 105 2-895-565-31 cabinet (rear) (sp, e41, aus) 106 3-198-219-01 cushion, cap 107 4-233-372-02 foot (felt) 108 2-067-415-01 terminal (+, ?, battery 109 2-895-597-01 terminal (?, battery 110 a-1244-301-a battery board, complete 111 3-252-830-01 screw (b3), (+) pwh tapping 112 a-1244-302-a d-light board, complete (g700cp) 113 3-238-135-01 terminal (?, battery 114 3-096-719-01 sheet (rear) 0 f902 1-532-504-33 fuse (t4al/250v) 0 j901 1-526-838-11 inlet, ac 2p ( - ac in) (sp, e41, aus) 0 j901 1-540-009-11 inlet, ac ( - ac in) (us, cnd, mx, e92) 0 t901 1-435-964-12 transformer, power (us, cnd, mx, e92) 0 t901 1-435-965-12 transformer, power (sp, e41, aus) t901 f902 j901 111 101 102 103 101 104 107 108 109 109 105 101 114 112 110 113 101 101 101 g700cp not supplied 106 106 106 106 106 106 106 106
54 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark 8-4. cabinet (upper) section-1 151 2-108-743-01 cushion key cassette 152 2-895-588-01 button, rec 153 2-895-589-01 button, play 154 2-895-590-01 button, rew 155 2-895-591-01 button, ff 156 2-895-592-01 button, stop 157 2-895-593-01 button, pause 158 3-252-827-01 screw (b2.6), (+) bv tapping 159 3-923-736-01 cover, cd 0 160 8-820-126-02 optical pick-up (ksm-213cdp/c2np) 161 3-931-379-21 rubber, vibration proof 162 3-931-379-31 rubber, vibration proof 163 3-252-828-01 screw (b2.6), (+) pwh tapping 164 1-832-404-21 cable, flexible flat (16 core) 165 a-1244-423-a bd90 board, complete 166 1-832-613-21 cable, flexible flat (21 core) 167 a-1244-418-a tuner board, complete (us, cnd, mx, e92) 167 a-1244-419-a tuner board, complete (sp, e41, aus) 168 3-254-143-11 screw (b3), (+) bv tapping 169 a-1244-300-a main board, complete (mx, e92) 169 a-1244-370-a main board, complete (g700cp) 169 a-1244-371-a main board, complete (cnd) 169 a-1244-372-a main board, complete (sp) 169 a-1244-373-a main board, complete (e41) 169 a-1244-374-a main board, complete (aus) 170 2-895-061-01 terminal, antenna s201 1-771-853-11 switch, detection (limit) #1 7-685-853-04 screw +bvtt 2x6 (s) 169 168 #1 168 152 153 151 156 157 155 159 160 162 164 163 163 167 170 158 165 166 161 154 168 tape mechanism deck section not supplied not supplied s201 cabinet (upper) section-2
55 CFD-G700CP/g770cp/g770cpk 201 2-895-568-01 panel (upper) (g770cp/g770cpk) 201 2-895-568-11 panel (upper) (g700cp) 202 2-895-060-01 spring, cassette 203 2-895-572-01 lid, cassette (g770cpk) 203 2-895-572-11 lid, cassette (g700cp) 203 2-895-572-21 lid, cassette (g770cp) 204 2-895-571-01 lid, cd 205 1-754-376-11 antenna, telescopic 206 1-452-899-11 magnet 207 3-019-395-01 plate, chucking 208 3-253-143-01 screw (b2.6), (+) p tapping 209 2-895-059-01 spring, cd 210 3-252-833-01 screw (m3), (+) p 211 3-831-441-11 cushion (b) 212 3-047-468-21 damper 213 2-895-586-01 button, cd 214 a-1244-299-a cd key board, complete 215 3-252-827-01 screw (b2.6), (+) bv tapping 216 a-1244-298-a woofer key board, complete 217 2-895-587-01 button, sound 218 3-047-468-01 damper 219 3-254-143-11 screw (b3), (+) bv tapping 220 2-895-566-01 cabinet (upper) (g770cp/g770cpk) 220 2-895-566-11 cabinet (upper) (g700cp) 221 2-895-760-01 sheet (x plod) sw2 1-692-960-11 switch, push (1 key) ( z push open/close) ref. no. part no. description remark ref. no. part no. description remark 8-5. cabinet (upper) section-2 207 206 202 221 204 203 208 209 218 219 201 217 216 212 220 214 213 211 211 205 215 215 215 210 not supplied not supplied sw2
56 CFD-G700CP/g770cp/g770cpk 251 2-670-389-01 belt (1) 252 2-670-390-01 belt (2) 253 1-797-375-11 deck, mechanical (h21sb-c05) 254 3-254-029-01 screw 255 3-254-022-01 screw ref. no. part no. description remark ref. no. part no. description remark 8-6. tape mechanism deck section 251 252 256 257 258 254 254 255 253 not supplied not supplied not supplied not supplied not supplied not supplied not supplied 256 a-1246-280-a tc board, complete 257 2-659-455-01 holder (rec) 258 3-252-612-01 lever, rec
57 CFD-G700CP/g770cp/g770cpk section 9 electrical parts list note: due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -xx and -x mean standardized parts, so they may have some difference from the original one. items marked ??are not stocked since they are seldom required for routine service. some delay should be anticipated when ordering these items. accessories are given in the last of this parts list. capacitors uf: f coils uh: h resistors all resistors are in ohms. metal: metal-film resistor. metal oxide: metal oxide-film resistor. f: nonflammable semiconductors in each case, u: , for example: ua. . : a. . upa. . : p a. . upb. . : pb. . upc. . : pc. . upd. . : pd. . ? bb re viation au s: australian model cnd : canadian model e41 : ac 230v area in e model e92 : ac 120v area in e model mx : mexican model sp : singapore model ref. no. part no. description remark ref. no. part no. description remark a-1244-296-a audio in board, complete ************************ < connector > cnp357 1-815-551-11 pin, connector (pwb) 3p < jack > j402 1-815-629-11 jack (audio in) < jumper resistor > jr205 1-216-864-11 short chip 0 jr206 1-216-864-11 short chip 0 < coil > l101 1-410-517-11 inductor 47uh l102 1-410-517-11 inductor 47uh l202 1-410-517-11 inductor 47uh < resistor > r121 1-216-837-11 metal chip 22k 5% 1/10w r122 1-216-837-11 metal chip 22k 5% 1/10w r221 1-216-837-11 metal chip 22k 5% 1/10w r222 1-216-837-11 metal chip 22k 5% 1/10w ************************************************************* a-1244-301-a battery board, complete ************************ 3-238-135-01 terminal (?, battery < connector > cnp941 1-815-552-11 pin, connector (pwb) 4p ************************************************************* a-1244-423-a bd90 board, complete ******************** < capacitor > c100 1-164-360-11 ceramic chip 0.1uf 16v c101 1-164-360-11 ceramic chip 0.1uf 16v c102 1-164-360-11 ceramic chip 0.1uf 16v c103 1-164-360-11 ceramic chip 0.1uf 16v c104 1-164-360-11 ceramic chip 0.1uf 16v c105 1-164-360-11 ceramic chip 0.1uf 16v c106 1-128-995-21 elect chip 100uf 20% 10v c107 1-164-360-11 ceramic chip 0.1uf 16v c108 1-164-360-11 ceramic chip 0.1uf 16v c109 1-164-360-11 ceramic chip 0.1uf 16v c110 1-164-360-11 ceramic chip 0.1uf 16v c112 1-164-360-11 ceramic chip 0.1uf 16v c113 1-164-360-11 ceramic chip 0.1uf 16v c115 1-124-778-00 elect chip 22uf 20% 6.3v c116 1-164-360-11 ceramic chip 0.1uf 16v c117 1-164-227-11 ceramic chip 0.022uf 10% 25v c118 1-162-970-11 ceramic chip 0.01uf 10% 25v c119 1-164-227-11 ceramic chip 0.022uf 10% 25v c120 1-162-970-11 ceramic chip 0.01uf 10% 25v c122 1-164-315-11 ceramic chip 470pf 5% 50v c123 1-164-315-11 ceramic chip 470pf 5% 50v c124 1-162-968-11 ceramic chip 0.0047uf 10% 50v c125 1-162-968-11 ceramic chip 0.0047uf 10% 50v c126 1-107-826-11 ceramic chip 0.1uf 10% 16v c127 1-162-966-11 ceramic chip 0.0022uf 10% 50v c128 1-162-910-11 ceramic chip 5pf 0.25pf 50v c130 1-162-910-11 ceramic chip 5pf 0.25pf 50v c132 1-164-360-11 ceramic chip 0.1uf 16v c133 1-107-826-11 ceramic chip 0.1uf 10% 16v c136 1-162-923-11 ceramic chip 47pf 5% 50v c137 1-162-970-11 ceramic chip 0.01uf 10% 25v c138 1-164-315-11 ceramic chip 470pf 5% 50v c139 1-162-970-11 ceramic chip 0.01uf 10% 25v c140 1-162-970-11 ceramic chip 0.01uf 10% 25v c141 1-162-966-11 ceramic chip 0.0022uf 10% 50v c142 1-107-826-11 ceramic chip 0.1uf 10% 16v c143 1-162-970-11 ceramic chip 0.01uf 10% 25v c144 1-107-826-11 ceramic chip 0.1uf 10% 16v c145 1-162-970-11 ceramic chip 0.01uf 10% 25v c146 1-164-315-11 ceramic chip 470pf 5% 50v c147 1-107-826-11 ceramic chip 0.1uf 10% 16v c148 1-162-923-11 ceramic chip 47pf 5% 50v c149 1-162-919-11 ceramic chip 22pf 5% 50v c150 1-162-964-11 ceramic chip 0.001uf 10% 50v c151 1-164-315-11 ceramic chip 470pf 5% 50v c152 1-164-315-11 ceramic chip 470pf 5% 50v c153 1-164-360-11 ceramic chip 0.1uf 16v c201 1-128-995-21 elect chip 100uf 20% 10v when indicating parts by reference number, please include the board name. the components identified by mark 0 or dotted line with mark 0 are critical for safety. replace only with part number specified. les composants identifi?s par une marque 0 sont critiques pour la s?curit?. ne les remplacer que par une pi?ce portant le num?ro sp?cifi?. a udio in ba ttery bd90
58 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark c202 1-128-995-21 elect chip 100uf 20% 10v c204 1-164-360-11 ceramic chip 0.1uf 16v c205 1-164-360-11 ceramic chip 0.1uf 16v c206 1-165-908-11 ceramic chip 1uf 10% 10v c207 1-165-908-11 ceramic chip 1uf 10% 10v c301 1-164-360-11 ceramic chip 0.1uf 16v c302 1-137-710-91 ceramic chip 10uf 20% 6.3v c303 1-137-710-91 ceramic chip 10uf 20% 6.3v c306 1-128-995-21 elect chip 100uf 20% 10v c307 1-165-908-11 ceramic chip 1uf 10% 10v c309 1-162-964-11 ceramic chip 0.001uf 10% 50v c401 1-128-394-11 elect chip 220uf 20% 10v c403 1-164-360-11 ceramic chip 0.1uf 16v c404 1-164-360-11 ceramic chip 0.1uf 16v c405 1-164-360-11 ceramic chip 0.1uf 16v < connector > cn201 1-784-833-51 connector, ffc (lif (non-zif)) 21p cn301 1-770-425-51 connector, ffc/fpc 16p < ic > ic101 (not supplied) ic tc94a70fg-006 ic201 6-710-808-01 ic tk63115scl-g@gt ic401 6-710-637-01 ic ba5826sfp-e2 < transistor > q301 6-551-120-01 transistor 2sa2119k < resistor > r101 1-216-813-11 metal chip 220 5% 1/10w r102 1-216-833-11 metal chip 10k 5% 1/10w r104 1-216-295-91 short chip 0 r105 1-216-857-11 metal chip 1m 5% 1/10w r106 1-216-821-11 metal chip 1k 5% 1/10w r108 1-216-864-11 short chip 0 r110 1-216-833-11 metal chip 10k 5% 1/10w r111 1-216-809-11 metal chip 100 5% 1/10w r112 1-216-809-11 metal chip 100 5% 1/10w r113 1-216-833-11 metal chip 10k 5% 1/10w r114 1-216-833-11 metal chip 10k 5% 1/10w r118 1-216-845-11 metal chip 100k 5% 1/10w r120 1-216-864-11 short chip 0 r125 1-216-864-11 short chip 0 r126 1-216-864-11 short chip 0 r127 1-216-864-11 short chip 0 r128 1-216-853-11 metal chip 470k 5% 1/10w r129 1-216-821-11 metal chip 1k 5% 1/10w r130 1-216-829-11 metal chip 4.7k 5% 1/10w r134 1-216-857-11 metal chip 1m 5% 1/10w r135 1-216-853-11 metal chip 470k 5% 1/10w r136 1-216-837-11 metal chip 22k 5% 1/10w r139 1-216-841-11 metal chip 47k 5% 1/10w r140 1-216-864-11 short chip 0 r142 1-216-837-11 metal chip 22k 5% 1/10w r143 1-216-841-11 metal chip 47k 5% 1/10w r144 1-216-837-11 metal chip 22k 5% 1/10w r145 1-216-864-11 short chip 0 r146 1-216-864-11 short chip 0 r147 1-216-864-11 short chip 0 r148 1-216-864-11 short chip 0 r149 1-216-864-11 short chip 0 r150 1-216-864-11 short chip 0 r151 1-216-864-11 short chip 0 r153 1-216-857-11 metal chip 1m 5% 1/10w r154 1-216-857-11 metal chip 1m 5% 1/10w r155 1-216-805-11 metal chip 47 5% 1/10w r156 1-216-809-11 metal chip 100 5% 1/10w r157 1-216-809-11 metal chip 100 5% 1/10w r201 1-216-295-91 short chip 0 r202 1-216-295-91 short chip 0 r203 1-216-809-11 metal chip 100 5% 1/10w r204 1-216-809-11 metal chip 100 5% 1/10w r205 1-216-809-11 metal chip 100 5% 1/10w r206 1-216-809-11 metal chip 100 5% 1/10w r207 1-216-809-11 metal chip 100 5% 1/10w r208 1-216-809-11 metal chip 100 5% 1/10w r209 1-216-809-11 metal chip 100 5% 1/10w r210 1-216-809-11 metal chip 100 5% 1/10w r211 1-216-809-11 metal chip 100 5% 1/10w r212 1-216-809-11 metal chip 100 5% 1/10w r218 1-216-845-11 metal chip 100k 5% 1/10w r219 1-216-845-11 metal chip 100k 5% 1/10w r220 1-216-845-11 metal chip 100k 5% 1/10w r221 1-216-845-11 metal chip 100k 5% 1/10w r222 1-216-845-11 metal chip 100k 5% 1/10w r223 1-216-845-11 metal chip 100k 5% 1/10w r301 1-216-845-11 metal chip 100k 5% 1/10w r302 1-216-864-11 short chip 0 r303 1-216-789-11 metal chip 2.2 5% 1/10w r304 1-216-789-11 metal chip 2.2 5% 1/10w r402 1-216-825-11 metal chip 2.2k 5% 1/10w r405 1-216-833-11 metal chip 10k 5% 1/10w r408 1-216-825-11 metal chip 2.2k 5% 1/10w r414 1-216-829-11 metal chip 4.7k 5% 1/10w r415 1-216-841-11 metal chip 47k 5% 1/10w < vibrator > x102 1-795-101-21 vibrator, ceramic (16.934mhz) ************************************************************* a-1244-299-a cd key board, complete *********************** 3-831-441-11 cushion (b) < resistor > r404 1-216-821-11 metal chip 1k 5% 1/10w r405 1-216-825-11 metal chip 2.2k 5% 1/10w r406 1-216-821-11 metal chip 1k 5% 1/10w r407 1-216-825-11 metal chip 2.2k 5% 1/10w r410 1-216-813-11 metal chip 220 5% 1/10w r421 1-216-817-11 metal chip 470 5% 1/10w r422 1-216-821-11 metal chip 1k 5% 1/10w r466 1-216-809-11 metal chip 100 5% 1/10w cd key bd90
59 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark < switch > s401 1-786-050-21 switch, key board (tune ? ? s402 1-786-050-21 switch, key board (tune +/ +) s405 1-786-050-21 switch, key board ( u) s406 1-786-050-21 switch, key board ( x ) s413 1-786-050-21 switch, key board (preset ? . ) s414 1-786-050-21 switch, key board (preset + > ) ************************************************************* a-1244-302-a d-light board, complete (g700cp) *********************** < jack > j103 1-820-048-11 connector (lighting) (d-light sync out) < resistor > l302 1-216-864-11 short chip 0 l306 1-216-864-11 short chip 0 l307 1-216-864-11 short chip 0 ************************************************************* a-1244-297-a headphone board, complete *************************** < connector > cnp392 1-815-552-11 pin, connector (pwb) 4p < jack > j391 1-794-016-11 jack ( i ) < coil > l301 1-410-509-11 inductor 10uh < resistor > r192 1-216-821-11 metal chip 1k 5% 1/10w r193 1-216-813-11 metal chip 220 5% 1/10w r194 1-216-813-11 metal chip 220 5% 1/10w r292 1-216-821-11 metal chip 1k 5% 1/10w r293 1-216-813-11 metal chip 220 5% 1/10w r294 1-216-813-11 metal chip 220 5% 1/10w ************************************************************* a-1244-292-a lcd board, complete ******************** 1-831-799-21 cable, flexible flat (19 core) 2-895-582-01 holder, lcd 3-198-120-01 sheet (ir), adhesive < capacitor > c401 1-115-156-11 ceramic chip 1uf 10v < diode > d406 8-719-059-97 diode l-34hd (opr/batt) < ic > ic891 6-701-681-01 ic rpm7140-v4 < liquid crystal display > lcd401 1-802-396-11 display panel, liquid crystal < resistor > r428 1-216-813-11 metal chip 220 5% 1/10w r469 1-216-845-11 metal chip 100k 5% 1/10w r475 1-216-849-11 metal chip 220k 5% 1/10w ************************************************************* a-1243-618-a led1 board, complete ******************** < resistor > r471 1-216-813-11 metal chip 220 5% 1/10w r472 1-216-813-11 metal chip 220 5% 1/10w ************************************************************* a-1243-619-a led2 board, complete ******************** < resistor > r449 1-216-813-11 metal chip 220 5% 1/10w r450 1-216-813-11 metal chip 220 5% 1/10w ************************************************************* a-1243-620-a led3 board, complete ******************** < resistor > r476 1-216-813-11 metal chip 220 5% 1/10w r487 1-216-813-11 metal chip 220 5% 1/10w ************************************************************* a-1243-621-a led4 board, complete ******************** < resistor > r478 1-216-813-11 metal chip 220 5% 1/10w r479 1-216-813-11 metal chip 220 5% 1/10w ************************************************************* a-1244-300-a main board, complete (mx, e92) a-1244-370-a main board, complete (g700cp) a-1244-371-a main board, complete (cnd) a-1244-372-a main board, complete (sp) a-1244-373-a main board, complete (e41) a-1244-374-a main board, complete (aus) ********************* 1-832-425-21 cable, flexible flat (11 core) 1-833-945-21 cable, flexible flat (11 core) 3-252-827-01 screw (b2.6), (+) bv tapping < capacitor > c106 1-107-826-11 ceramic chip 0.1uf 10% 16v c107 1-107-826-11 ceramic chip 0.1uf 10% 16v c108 1-165-176-11 ceramic chip 0.047uf 10% 16v c109 1-165-176-11 ceramic chip 0.047uf 10% 16v c110 1-162-968-11 ceramic chip 0.0047uf 10% 50v c111 1-162-966-11 ceramic chip 0.0022uf 10% 50v c121 1-126-960-11 elect 1uf 20% 50v led1 lcd cd key d-light headphone led2 led3 led4 main
60 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark c123 1-126-961-11 elect 2.2uf 20% 50v c124 1-162-927-11 ceramic chip 100pf 5% 50v c125 1-126-963-11 elect 4.7uf 20% 50v c126 1-126-961-11 elect 2.2uf 20% 50v c127 1-126-960-11 elect 1uf 20% 50v c131 1-126-959-11 elect 0.47uf 20% 50v c132 1-162-927-11 ceramic chip 100pf 5% 50v c151 1-126-964-11 elect 10uf 20% 50v (g770cpk) c152 1-126-960-11 elect 1uf 20% 50v (g770cpk) c153 1-126-960-11 elect 1uf 20% 50v (mx, e92, aus) c153 1-126-964-11 elect 10uf 20% 50v (cnd) c154 1-162-960-11 ceramic chip 220pf 10% 50v (g770cpk) c161 1-126-960-11 elect 1uf 20% 50v c171 1-126-947-11 elect 47uf 20% 35v c172 1-162-962-11 ceramic chip 470pf 10% 50v c173 1-104-658-91 elect 100uf 20% 10v c174 1-126-926-11 elect 1000uf 20% 10v c175 1-164-156-11 ceramic chip 0.1uf 25v c206 1-107-826-11 ceramic chip 0.1uf 10% 16v c207 1-107-826-11 ceramic chip 0.1uf 10% 16v c208 1-165-176-11 ceramic chip 0.047uf 10% 16v c209 1-165-176-11 ceramic chip 0.047uf 10% 16v c210 1-162-968-11 ceramic chip 0.0047uf 10% 50v c211 1-162-966-11 ceramic chip 0.0022uf 10% 50v c221 1-126-960-11 elect 1uf 20% 50v c223 1-126-961-11 elect 2.2uf 20% 50v c224 1-162-927-11 ceramic chip 100pf 5% 50v c225 1-126-963-11 elect 4.7uf 20% 50v c226 1-126-961-11 elect 2.2uf 20% 50v c227 1-126-960-11 elect 1uf 20% 50v c231 1-126-959-11 elect 0.47uf 20% 50v c232 1-162-927-11 ceramic chip 100pf 5% 50v c251 1-126-964-11 elect 10uf 20% 50v (g770cpk) c252 1-126-960-11 elect 1uf 20% 50v (g770cpk) c253 1-126-960-11 elect 1uf 20% 50v (mx, e92, aus) c253 1-126-964-11 elect 10uf 20% 50v (cnd) c254 1-162-960-11 ceramic chip 220pf 10% 50v (g770cpk) c261 1-126-960-11 elect 1uf 20% 50v c271 1-126-947-11 elect 47uf 20% 35v c272 1-162-962-11 ceramic chip 470pf 10% 50v c273 1-104-658-91 elect 100uf 20% 10v c274 1-126-926-11 elect 1000uf 20% 10v c275 1-164-156-11 ceramic chip 0.1uf 25v c301 1-126-923-91 elect 220uf 20% 10v (g770cpk) c302 1-115-156-11 ceramic chip 1uf 10v c303 1-126-964-11 elect 10uf 20% 50v c304 1-107-826-11 ceramic chip 0.1uf 10% 16v c305 1-126-935-11 elect 470uf 20% 16v c326 1-165-176-11 ceramic chip 0.047uf 10% 16v c327 1-164-227-11 ceramic chip 0.022uf 10% 25v c332 1-126-960-11 elect 1uf 20% 50v (g700cp) c333 1-162-970-11 ceramic chip 0.01uf 10% 25v c334 1-164-227-11 ceramic chip 0.022uf 10% 25v c335 1-126-960-11 elect 1uf 20% 50v c336 1-126-923-91 elect 220uf 20% 10v c337 1-126-960-11 elect 1uf 20% 50v (g700cp) c338 1-126-964-11 elect 10uf 20% 50v c339 1-104-658-91 elect 100uf 20% 10v c340 1-104-658-91 elect 100uf 20% 10v c341 1-104-662-91 elect 22uf 20% 25v c342 1-162-927-11 ceramic chip 100pf 5% 50v c343 1-126-964-11 elect 10uf 20% 50v c344 1-126-964-11 elect 10uf 20% 50v (g700cp) c345 1-126-964-11 elect 10uf 20% 50v c346 1-126-942-61 elect 1000uf 20% 25v c347 1-126-964-11 elect 10uf 20% 50v c348 1-126-946-11 elect 6800uf 20% 25v c349 1-104-666-11 elect 220uf 20% 25v c350 1-162-995-11 ceramic chip 0.022uf 50v c351 1-104-658-91 elect 100uf 20% 10v c352 1-107-826-11 ceramic chip 0.1uf 10% 16v c353 1-104-658-91 elect 100uf 20% 10v c354 1-104-658-91 elect 100uf 20% 10v c355 1-104-658-91 elect 100uf 20% 10v c356 1-104-658-91 elect 100uf 20% 10v c357 1-164-156-11 ceramic chip 0.1uf 25v c358 1-164-156-11 ceramic chip 0.1uf 25v c359 1-104-662-91 elect 22uf 20% 25v c360 1-126-961-11 elect 2.2uf 20% 50v c361 1-162-970-11 ceramic chip 0.01uf 10% 25v c362 1-126-964-11 elect 10uf 20% 50v c366 1-162-927-11 ceramic chip 100pf 5% 50v c371 1-104-658-91 elect 100uf 20% 10v c380 1-126-923-91 elect 220uf 20% 10v c381 1-104-658-91 elect 100uf 20% 10v (g700cp) c402 1-126-960-11 elect 1uf 20% 50v (g770cpk) c411 1-162-927-11 ceramic chip 100pf 5% 50v c415 1-164-227-11 ceramic chip 0.022uf 10% 25v (g770cpk) c416 1-104-658-91 elect 100uf 20% 10v (g770cpk) c417 1-126-963-11 elect 4.7uf 20% 50v (g770cpk) c418 1-126-963-11 elect 4.7uf 20% 50v (g770cpk) c419 1-104-658-91 elect 100uf 20% 10v (g770cpk) c420 1-126-947-11 elect 47uf 20% 35v (g770cpk) c421 1-126-960-11 elect 1uf 20% 50v (g770cpk) c422 1-126-947-11 elect 47uf 20% 35v (g770cpk) main
61 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark c423 1-104-662-91 elect 22uf 20% 25v (g770cpk) c424 1-126-964-11 elect 10uf 20% 50v (g770cpk) c425 1-127-715-91 ceramic chip 0.22uf 10% 16v (g770cpk) c426 1-127-715-91 ceramic chip 0.22uf 10% 16v (g770cpk) c427 1-126-963-11 elect 4.7uf 20% 50v (g770cpk) c430 1-115-156-11 ceramic chip 1uf 10v c431 1-162-927-11 ceramic chip 100pf 5% 50v (g770cpk) c432 1-162-927-11 ceramic chip 100pf 5% 50v (g770cpk) c433 1-162-927-11 ceramic chip 100pf 5% 50v (g770cpk) c436 1-164-156-11 ceramic chip 0.1uf 25v c437 1-100-591-91 ceramic chip 1uf 10% 25v c451 1-162-913-11 ceramic chip 8pf 0.5pf 50v c453 1-162-919-11 ceramic chip 22pf 5% 50v c454 1-162-923-11 ceramic chip 47pf 5% 50v c455 1-162-923-11 ceramic chip 47pf 5% 50v c456 1-162-919-11 ceramic chip 22pf 5% 50v c457 1-162-970-11 ceramic chip 0.01uf 10% 25v c458 1-162-970-11 ceramic chip 0.01uf 10% 25v c459 1-162-915-11 ceramic chip 10pf 0.5pf 50v c461 1-126-964-11 elect 10uf 20% 50v c803 1-164-156-11 ceramic chip 0.1uf 25v c804 1-162-970-11 ceramic chip 0.01uf 10% 25v c805 1-104-658-91 elect 100uf 20% 10v c806 1-115-156-11 ceramic chip 1uf 10v c807 1-162-970-11 ceramic chip 0.01uf 10% 25v c808 1-104-658-91 elect 100uf 20% 10v c810 1-162-970-11 ceramic chip 0.01uf 10% 25v c813 1-107-826-11 ceramic chip 0.1uf 10% 16v c814 1-107-826-11 ceramic chip 0.1uf 10% 16v c815 1-107-826-11 ceramic chip 0.1uf 10% 16v c816 1-162-927-11 ceramic chip 100pf 5% 50v c819 1-107-826-11 ceramic chip 0.1uf 10% 16v c820 1-107-826-11 ceramic chip 0.1uf 10% 16v c825 1-115-156-11 ceramic chip 1uf 10v c826 1-162-964-11 ceramic chip 0.001uf 10% 50v c827 1-162-968-11 ceramic chip 0.0047uf 10% 50v c828 1-162-964-11 ceramic chip 0.001uf 10% 50v c829 1-162-927-11 ceramic chip 100pf 5% 50v (g770cpk) c831 1-162-927-11 ceramic chip 100pf 5% 50v c833 1-162-927-11 ceramic chip 100pf 5% 50v c837 1-162-927-11 ceramic chip 100pf 5% 50v c839 1-164-230-11 ceramic chip 220pf 5% 50v c841 1-162-927-11 ceramic chip 100pf 5% 50v c842 1-162-927-11 ceramic chip 100pf 5% 50v c843 1-162-927-11 ceramic chip 100pf 5% 50v c846 1-162-927-11 ceramic chip 100pf 5% 50v c847 1-162-970-11 ceramic chip 0.01uf 10% 25v c848 1-162-970-11 ceramic chip 0.01uf 10% 25v c849 1-162-970-11 ceramic chip 0.01uf 10% 25v c850 1-162-970-11 ceramic chip 0.01uf 10% 25v c851 1-162-927-11 ceramic chip 100pf 5% 50v c852 1-162-927-11 ceramic chip 100pf 5% 50v c853 1-162-927-11 ceramic chip 100pf 5% 50v c854 1-162-927-11 ceramic chip 100pf 5% 50v c855 1-162-927-11 ceramic chip 100pf 5% 50v c856 1-162-927-11 ceramic chip 100pf 5% 50v c857 1-162-927-11 ceramic chip 100pf 5% 50v c951 1-164-227-11 ceramic chip 0.022uf 10% 25v c953 1-164-227-11 ceramic chip 0.022uf 10% 25v c954 1-126-934-11 elect 220uf 20% 16v c955 1-164-227-11 ceramic chip 0.022uf 10% 25v c957 1-126-923-91 elect 220uf 20% 10v c961 1-126-923-91 elect 220uf 20% 10v c962 1-164-227-11 ceramic chip 0.022uf 10% 25v (g700cp) < connector > * cn799 1-784-732-11 connector, ffc 10p cn803 1-784-741-11 connector, ffc 19p cn804 1-784-741-11 connector, ffc 19p cn805 1-779-289-11 connector, ffc (lif (non-zif)) 21p < connector > cnp301 1-815-553-21 pin, connector (pwb) 5p cnp303 1-815-554-11 pin, connector (pwb) 6p cnp390 1-815-554-11 pin, connector (pwb) 6p (g770cpk) cnp391 1-815-553-11 pin, connector (pwb) 5p cnp393 1-815-552-11 pin, connector (pwb) 4p cnp394 1-815-551-11 pin, connector (pwb) 3p cnp397 1-815-551-11 pin, connector (pwb) 3p (g700cp) cnp803 1-815-550-31 pin, connector (pwb) 2p cnp805 1-815-551-11 pin, connector (pwb) 3p cnp806 1-815-550-21 pin, connector (pwb) 2p cnp807 1-815-550-11 pin, connector (pwb) 2p < diode > d320 6-500-335-01 diode mc2838-t112-1 d321 6-501-193-01 diode 1ss355wte-17 d322 6-501-193-01 diode 1ss355wte-17 d323 6-501-193-01 diode 1ss355wte-17 d324 6-500-335-01 diode mc2838-t112-1 d351 6-501-579-01 diode mc2837 d414 6-501-193-01 diode 1ss355wte-17 (g770cpk) d415 6-500-334-01 diode mc2836-t112-1 (g770cpk) d461 6-500-335-01 diode mc2838-t112-1 d462 8-719-069-54 diode udzste-175.1b d801 6-500-334-01 diode mc2836-t112-1 d802 6-500-334-01 diode mc2836-t112-1 d804 6-501-193-01 diode 1ss355wte-17 (g770cpk) d805 6-501-193-01 diode 1ss355wte-17 d951 6-501-193-01 diode 1ss355wte-17 d952 6-500-334-01 diode mc2836-t112-1 d953 6-501-193-01 diode 1ss355wte-17 d954 8-719-977-28 diode dtz10b d955 8-719-978-33 diode dtz-tt11-6.8b main
62 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark < ferrite bead > fb831 1-216-864-11 short chip 0 fb832 1-216-864-11 short chip 0 fb833 1-216-864-11 short chip 0 fb834 1-216-864-11 short chip 0 fb835 1-414-760-21 ferrite, emi (smd) (1608) fb836 1-414-760-21 ferrite, emi (smd) (1608) fb837 1-216-864-11 short chip 0 < ic > ic321 6-710-289-01 ic r2s15904sp ic351 8-759-426-51 ic ba5417 ic371 8-759-426-51 ic ba5417 ic401 8-759-332-64 ic ba3837 (g770cpk) ic801 6-807-359-01 ic mb90802npf-g-127e1 ic802 6-710-820-01 ic s-24cs02afj-tb-g ic805 6-704-118-01 ic s-80828cnmc-b8nt2g ic806 6-706-338-01 ic xc6202p332fr ic901 6-710-863-01 ic tk70540scl-g (g700cp) ic902 6-702-771-01 ic ta78033ls < jumper resistor > jr105 1-216-864-11 short chip 0 jr106 1-216-864-11 short chip 0 jr107 1-216-864-11 short chip 0 jr108 1-216-864-11 short chip 0 jr109 1-216-864-11 short chip 0 jr110 1-216-864-11 short chip 0 jr111 1-216-864-11 short chip 0 jr113 1-216-864-11 short chip 0 jr114 1-216-864-11 short chip 0 jr117 1-216-864-11 short chip 0 jr118 1-216-864-11 short chip 0 jr120 1-216-864-11 short chip 0 jr121 1-216-864-11 short chip 0 jr122 1-216-864-11 short chip 0 jr124 1-216-864-11 short chip 0 jr126 1-216-864-11 short chip 0 jr127 1-216-864-11 short chip 0 jr128 1-216-864-11 short chip 0 jr129 1-216-864-11 short chip 0 jr131 1-216-864-11 short chip 0 jr133 1-216-864-11 short chip 0 jr134 1-216-864-11 short chip 0 jr135 1-216-864-11 short chip 0 jr136 1-216-864-11 short chip 0 jr137 1-216-864-11 short chip 0 jr138 1-216-864-11 short chip 0 jr140 1-216-864-11 short chip 0 jr150 1-216-864-11 short chip 0 jr151 1-216-864-11 short chip 0 jr152 1-216-864-11 short chip 0 jr153 1-216-864-11 short chip 0 jr155 1-216-864-11 short chip 0 < coil > l158 1-410-501-11 inductor 2.2uh l159 1-410-501-11 inductor 2.2uh l160 1-410-501-11 inductor 2.2uh l803 1-414-743-21 inductor 47uh < transistor > q171 8-729-620-07 transistor 2sc3052ef-t1-lef q271 8-729-620-07 transistor 2sc3052ef-t1-lef q320 8-729-620-07 transistor 2sc3052ef-t1-lef (g700cp) q321 8-729-620-07 transistor 2sc3052ef-t1-lef q322 8-729-620-07 transistor 2sc3052ef-t1-lef q323 8-729-045-62 transistor 2sk2158-t2b q351 8-729-036-89 transistor ktc3198gr-at q352 6-551-443-01 transistor rt1p436c-tp-1 q354 8-729-036-86 transistor ktc3203y-at q401 8-729-620-07 transistor 2sc3052ef-t1-lef (g770cpk) q402 8-729-620-07 transistor 2sc3052ef-t1-lef (g770cpk) q403 8-729-027-46 transistor dtc114yka-t146 (g770cpk) q405 8-729-620-07 transistor 2sc3052ef-t1-lef (g770cpk) q406 8-729-027-46 transistor dtc114yka-t146 (g770cpk) q407 8-729-027-46 transistor dtc114yka-t146 (g770cpk) q451 8-729-620-07 transistor 2sc3052ef-t1-lef q452 8-729-620-07 transistor 2sc3052ef-t1-lef q801 8-729-027-46 transistor dtc114yka-t146 q803 8-729-620-07 transistor 2sc3052ef-t1-lef q804 8-729-027-46 transistor dtc114yka-t146 q805 6-551-696-01 transistor isa1235ac1tp-1ef q806 6-551-444-01 transistor rt1n436c-tp-1 (sp, e41, aus) q812 8-729-027-46 transistor dtc114yka-t146 q815 8-729-027-26 transistor dta114yka-t146 q816 8-729-037-13 transistor kta1271y q950 8-729-037-13 transistor kta1271y q951 8-729-027-50 transistor dtc123jka-t146 q952 6-551-696-01 transistor isa1235ac1tp-1ef q953 6-551-276-01 transistor rt1n431c-tp-1 q954 8-729-036-86 transistor ktc3203y-at q959 8-729-027-46 transistor dtc114yka-t146 q971 8-729-037-08 transistor ktd2058y q972 8-729-037-08 transistor ktd2058y < resistor > r101 1-216-864-11 short chip 0 (g700cp/g770cp) r102 1-216-833-11 metal chip 10k 5% 1/10w r103 1-216-841-11 metal chip 47k 5% 1/10w r104 1-216-829-11 metal chip 4.7k 5% 1/10w r120 1-216-829-11 metal chip 4.7k 5% 1/10w r123 1-216-829-11 metal chip 4.7k 5% 1/10w r124 1-216-864-11 short chip 0 r125 1-216-837-11 metal chip 22k 5% 1/10w r126 1-216-841-11 metal chip 47k 5% 1/10w (g700cp) r127 1-216-833-11 metal chip 10k 5% 1/10w main
63 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark r129 1-216-864-11 short chip 0 r130 1-216-841-11 metal chip 47k 5% 1/10w r135 1-216-864-11 short chip 0 r151 1-216-833-11 metal chip 10k 5% 1/10w (g770cpk) r151 1-216-864-11 short chip 0 (g700cp/g770cp) r152 1-216-829-11 metal chip 4.7k 5% 1/10w (g770cpk) r153 1-216-829-11 metal chip 4.7k 5% 1/10w (g770cpk) r154 1-216-833-11 metal chip 10k 5% 1/10w (g770cpk) r160 1-216-841-11 metal chip 47k 5% 1/10w r161 1-216-821-11 metal chip 1k 5% 1/10w r162 1-216-841-11 metal chip 47k 5% 1/10w r172 1-216-833-11 metal chip 10k 5% 1/10w r173 1-216-825-11 metal chip 2.2k 5% 1/10w r175 1-216-813-11 metal chip 220 5% 1/10w r176 1-216-801-11 metal chip 22 5% 1/10w r179 1-216-829-11 metal chip 4.7k 5% 1/10w r181 1-216-793-11 metal chip 4.7 5% 1/10w r201 1-216-864-11 short chip 0 (g700cp/g770cp) r202 1-216-833-11 metal chip 10k 5% 1/10w r203 1-216-841-11 metal chip 47k 5% 1/10w r204 1-216-829-11 metal chip 4.7k 5% 1/10w r220 1-216-829-11 metal chip 4.7k 5% 1/10w r223 1-216-829-11 metal chip 4.7k 5% 1/10w r224 1-216-864-11 short chip 0 r225 1-216-837-11 metal chip 22k 5% 1/10w r226 1-216-841-11 metal chip 47k 5% 1/10w (g700cp) r227 1-216-833-11 metal chip 10k 5% 1/10w r229 1-216-864-11 short chip 0 r230 1-216-841-11 metal chip 47k 5% 1/10w r235 1-216-864-11 short chip 0 r251 1-216-833-11 metal chip 10k 5% 1/10w (g770cpk) r251 1-216-864-11 short chip 0 (g700cp/g770cp) r252 1-216-829-11 metal chip 4.7k 5% 1/10w (g770cpk) r253 1-216-829-11 metal chip 4.7k 5% 1/10w (g770cpk) r254 1-216-833-11 metal chip 10k 5% 1/10w (g770cpk) r261 1-216-821-11 metal chip 1k 5% 1/10w r262 1-216-864-11 short chip 0 r272 1-216-833-11 metal chip 10k 5% 1/10w r273 1-216-825-11 metal chip 2.2k 5% 1/10w r275 1-216-813-11 metal chip 220 5% 1/10w r276 1-216-801-11 metal chip 22 5% 1/10w r279 1-216-829-11 metal chip 4.7k 5% 1/10w r281 1-216-793-11 metal chip 4.7 5% 1/10w r317 1-216-833-11 metal chip 10k 5% 1/10w (g700cp) r318 1-216-853-11 metal chip 470k 5% 1/10w (g700cp) r319 1-216-829-11 metal chip 4.7k 5% 1/10w (g700cp) r322 1-216-864-11 short chip 0 r324 1-216-825-11 metal chip 2.2k 5% 1/10w r325 1-216-825-11 metal chip 2.2k 5% 1/10w r326 1-216-821-11 metal chip 1k 5% 1/10w r328 1-216-821-11 metal chip 1k 5% 1/10w r329 1-216-825-11 metal chip 2.2k 5% 1/10w r330 1-216-817-11 metal chip 470 5% 1/10w r331 1-216-837-11 metal chip 22k 5% 1/10w r332 1-216-853-11 metal chip 470k 5% 1/10w r333 1-216-833-11 metal chip 10k 5% 1/10w r334 1-216-817-11 metal chip 470 5% 1/10w r335 1-216-837-11 metal chip 22k 5% 1/10w r336 1-216-833-11 metal chip 10k 5% 1/10w r337 1-216-837-11 metal chip 22k 5% 1/10w r338 1-216-825-11 metal chip 2.2k 5% 1/10w r339 1-216-821-11 metal chip 1k 5% 1/10w r340 1-216-821-11 metal chip 1k 5% 1/10w r341 1-216-829-11 metal chip 4.7k 5% 1/10w r342 1-216-825-11 metal chip 2.2k 5% 1/10w r343 1-216-825-11 metal chip 2.2k 5% 1/10w r344 1-216-829-11 metal chip 4.7k 5% 1/10w r345 1-216-817-11 metal chip 470 5% 1/10w (g700cp) r346 1-216-805-11 metal chip 47 5% 1/10w (g700cp) r347 1-216-853-11 metal chip 470k 5% 1/10w r348 1-216-829-11 metal chip 4.7k 5% 1/10w r351 1-216-829-11 metal chip 4.7k 5% 1/10w r353 1-216-829-11 metal chip 4.7k 5% 1/10w r356 1-216-821-11 metal chip 1k 5% 1/10w r357 1-216-817-11 metal chip 470 5% 1/10w r359 1-216-797-11 metal chip 10 5% 1/10w r360 1-216-797-11 metal chip 10 5% 1/10w r361 1-216-825-11 metal chip 2.2k 5% 1/10w r362 1-216-817-11 metal chip 470 5% 1/10w r363 1-216-813-11 metal chip 220 5% 1/10w r364 1-216-857-11 metal chip 1m 5% 1/10w r365 1-216-857-11 metal chip 1m 5% 1/10w r366 1-216-833-11 metal chip 10k 5% 1/10w r371 1-216-833-11 metal chip 10k 5% 1/10w r372 1-216-833-11 metal chip 10k 5% 1/10w r409 1-216-821-11 metal chip 1k 5% 1/10w r418 1-216-821-11 metal chip 1k 5% 1/10w (g770cpk) r419 1-216-841-11 metal chip 47k 5% 1/10w (g770cpk) r420 1-216-829-11 metal chip 4.7k 5% 1/10w r427 1-216-821-11 metal chip 1k 5% 1/10w r429 1-216-825-11 metal chip 2.2k 5% 1/10w (g770cpk) r430 1-216-841-11 metal chip 47k 5% 1/10w (g770cpk) r431 1-216-817-11 metal chip 470 5% 1/10w (g770cpk) r432 1-216-821-11 metal chip 1k 5% 1/10w (g770cpk) r433 1-216-841-11 metal chip 47k 5% 1/10w (g770cpk) r434 1-216-821-11 metal chip 1k 5% 1/10w (g770cpk) main
64 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark r435 1-216-829-11 metal chip 4.7k 5% 1/10w (g770cpk) r436 1-216-825-11 metal chip 2.2k 5% 1/10w (g770cpk) r437 1-216-821-11 metal chip 1k 5% 1/10w (g770cpk) r438 1-216-821-11 metal chip 1k 5% 1/10w (g770cpk) r439 1-216-817-11 metal chip 470 5% 1/10w (g770cpk) r440 1-216-817-11 metal chip 470 5% 1/10w (g770cpk) r441 1-216-849-11 metal chip 220k 5% 1/10w (g770cpk) r444 1-216-845-11 metal chip 100k 5% 1/10w (g770cpk) r445 1-216-829-11 metal chip 4.7k 5% 1/10w (g770cpk) r446 1-216-817-11 metal chip 470 5% 1/10w (g770cpk) r447 1-216-841-11 metal chip 47k 5% 1/10w (g770cpk) r448 1-216-821-11 metal chip 1k 5% 1/10w r451 1-216-821-11 metal chip 1k 5% 1/10w r452 1-216-821-11 metal chip 1k 5% 1/10w r453 1-216-821-11 metal chip 1k 5% 1/10w r454 1-216-833-11 metal chip 10k 5% 1/10w r456 1-216-821-11 metal chip 1k 5% 1/10w r457 1-216-833-11 metal chip 10k 5% 1/10w r460 1-216-813-11 metal chip 220 5% 1/10w r461 1-216-817-11 metal chip 470 5% 1/10w r462 1-216-817-11 metal chip 470 5% 1/10w r463 1-216-813-11 metal chip 220 5% 1/10w r468 1-216-821-11 metal chip 1k 5% 1/10w r470 1-216-817-11 metal chip 470 5% 1/10w (g770cpk) r477 1-216-845-11 metal chip 100k 5% 1/10w r480 1-216-841-11 metal chip 47k 5% 1/10w r481 1-216-841-11 metal chip 47k 5% 1/10w r482 1-216-821-11 metal chip 1k 5% 1/10w r483 1-216-841-11 metal chip 47k 5% 1/10w r484 1-216-841-11 metal chip 47k 5% 1/10w r485 1-216-841-11 metal chip 47k 5% 1/10w r486 1-216-845-11 metal chip 100k 5% 1/10w r488 1-216-837-11 metal chip 22k 5% 1/10w r489 1-216-841-11 metal chip 47k 5% 1/10w (g770cpk) r490 1-216-864-11 short chip 0 r491 1-216-864-11 short chip 0 r492 1-216-864-11 short chip 0 r493 1-216-821-11 metal chip 1k 5% 1/10w r494 1-216-841-11 metal chip 47k 5% 1/10w (g770cpk) r495 1-216-845-11 metal chip 100k 5% 1/10w r800 1-216-825-11 metal chip 2.2k 5% 1/10w r801 1-216-817-11 metal chip 470 5% 1/10w r802 1-216-821-11 metal chip 1k 5% 1/10w r803 1-216-821-11 metal chip 1k 5% 1/10w r804 1-216-821-11 metal chip 1k 5% 1/10w r805 1-216-821-11 metal chip 1k 5% 1/10w r807 1-216-829-11 metal chip 4.7k 5% 1/10w r808 1-216-821-11 metal chip 1k 5% 1/10w r809 1-216-821-11 metal chip 1k 5% 1/10w r810 1-216-829-11 metal chip 4.7k 5% 1/10w r811 1-216-833-11 metal chip 10k 5% 1/10w r812 1-216-821-11 metal chip 1k 5% 1/10w r813 1-216-821-11 metal chip 1k 5% 1/10w r814 1-216-821-11 metal chip 1k 5% 1/10w r815 1-216-821-11 metal chip 1k 5% 1/10w r816 1-216-821-11 metal chip 1k 5% 1/10w r817 1-216-821-11 metal chip 1k 5% 1/10w r818 1-216-821-11 metal chip 1k 5% 1/10w r819 1-216-821-11 metal chip 1k 5% 1/10w r820 1-216-853-11 metal chip 470k 5% 1/10w r821 1-216-821-11 metal chip 1k 5% 1/10w r822 1-216-821-11 metal chip 1k 5% 1/10w r823 1-216-821-11 metal chip 1k 5% 1/10w r824 1-216-821-11 metal chip 1k 5% 1/10w r825 1-216-821-11 metal chip 1k 5% 1/10w r826 1-216-825-11 metal chip 2.2k 5% 1/10w (e41) r826 1-216-829-11 metal chip 4.7k 5% 1/10w (sp, aus) r827 1-216-825-11 metal chip 2.2k 5% 1/10w (sp) r827 1-216-829-11 metal chip 4.7k 5% 1/10w (e41, aus) r828 1-216-829-11 metal chip 4.7k 5% 1/10w r829 1-216-829-11 metal chip 4.7k 5% 1/10w r830 1-216-829-11 metal chip 4.7k 5% 1/10w r831 1-216-821-11 metal chip 1k 5% 1/10w (g770cpk) r834 1-216-833-11 metal chip 10k 5% 1/10w r835 1-216-833-11 metal chip 10k 5% 1/10w r836 1-216-833-11 metal chip 10k 5% 1/10w r837 1-216-833-11 metal chip 10k 5% 1/10w r838 1-216-833-11 metal chip 10k 5% 1/10w r839 1-216-841-11 metal chip 47k 5% 1/10w r840 1-216-833-11 metal chip 10k 5% 1/10w r841 1-216-833-11 metal chip 10k 5% 1/10w r842 1-216-833-11 metal chip 10k 5% 1/10w r843 1-216-833-11 metal chip 10k 5% 1/10w r844 1-216-833-11 metal chip 10k 5% 1/10w r845 1-216-833-11 metal chip 10k 5% 1/10w r846 1-216-833-11 metal chip 10k 5% 1/10w r847 1-216-833-11 metal chip 10k 5% 1/10w r848 1-216-833-11 metal chip 10k 5% 1/10w r849 1-216-833-11 metal chip 10k 5% 1/10w r850 1-216-833-11 metal chip 10k 5% 1/10w r851 1-216-833-11 metal chip 10k 5% 1/10w r852 1-216-833-11 metal chip 10k 5% 1/10w r853 1-216-833-11 metal chip 10k 5% 1/10w r854 1-216-833-11 metal chip 10k 5% 1/10w r855 1-216-833-11 metal chip 10k 5% 1/10w r856 1-216-833-11 metal chip 10k 5% 1/10w r857 1-216-833-11 metal chip 10k 5% 1/10w r858 1-216-833-11 metal chip 10k 5% 1/10w r859 1-216-833-11 metal chip 10k 5% 1/10w main
65 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark r860 1-216-833-11 metal chip 10k 5% 1/10w r861 1-216-833-11 metal chip 10k 5% 1/10w r862 1-216-833-11 metal chip 10k 5% 1/10w r863 1-216-833-11 metal chip 10k 5% 1/10w r864 1-216-821-11 metal chip 1k 5% 1/10w r865 1-216-821-11 metal chip 1k 5% 1/10w r866 1-216-833-11 metal chip 10k 5% 1/10w r867 1-216-833-11 metal chip 10k 5% 1/10w r868 1-216-817-11 metal chip 470 5% 1/10w r869 1-216-821-11 metal chip 1k 5% 1/10w (g770cpk) r870 1-216-821-11 metal chip 1k 5% 1/10w r871 1-216-817-11 metal chip 470 5% 1/10w r872 1-216-821-11 metal chip 1k 5% 1/10w r873 1-216-821-11 metal chip 1k 5% 1/10w r874 1-216-821-11 metal chip 1k 5% 1/10w r875 1-216-821-11 metal chip 1k 5% 1/10w r876 1-216-813-11 metal chip 220 5% 1/10w r877 1-216-821-11 metal chip 1k 5% 1/10w r878 1-216-821-11 metal chip 1k 5% 1/10w r879 1-216-833-11 metal chip 10k 5% 1/10w r880 1-216-821-11 metal chip 1k 5% 1/10w r881 1-216-833-11 metal chip 10k 5% 1/10w r882 1-216-833-11 metal chip 10k 5% 1/10w r883 1-216-821-11 metal chip 1k 5% 1/10w r884 1-216-817-11 metal chip 470 5% 1/10w (g770cpk) r885 1-216-821-11 metal chip 1k 5% 1/10w r886 1-216-841-11 metal chip 47k 5% 1/10w r887 1-216-841-11 metal chip 47k 5% 1/10w (g770cpk) r888 1-216-833-11 metal chip 10k 5% 1/10w (g700cp/g770cp) r888 1-216-841-11 metal chip 47k 5% 1/10w (g770cpk) r891 1-216-841-11 metal chip 47k 5% 1/10w r892 1-216-864-11 short chip 0 r893 1-216-864-11 short chip 0 (g700cp/g770cp) r894 1-216-797-11 metal chip 10 5% 1/10w r895 1-216-797-11 metal chip 10 5% 1/10w (g770cpk) r896 1-216-833-11 metal chip 10k 5% 1/10w r897 1-216-809-11 metal chip 100 5% 1/10w r898 1-216-829-11 metal chip 4.7k 5% 1/10w (us, cnd, mx, e92) r899 1-216-809-11 metal chip 100 5% 1/10w r900 1-216-841-11 metal chip 47k 5% 1/10w r901 1-216-841-11 metal chip 47k 5% 1/10w r902 1-216-821-11 metal chip 1k 5% 1/10w r903 1-216-821-11 metal chip 1k 5% 1/10w r904 1-216-821-11 metal chip 1k 5% 1/10w r905 1-216-821-11 metal chip 1k 5% 1/10w r906 1-216-821-11 metal chip 1k 5% 1/10w r907 1-216-833-11 metal chip 10k 5% 1/10w r941 1-216-825-11 metal chip 2.2k 5% 1/10w r942 1-216-825-11 metal chip 2.2k 5% 1/10w r943 1-216-825-11 metal chip 2.2k 5% 1/10w r944 1-216-825-11 metal chip 2.2k 5% 1/10w r945 1-216-825-11 metal chip 2.2k 5% 1/10w r946 1-216-825-11 metal chip 2.2k 5% 1/10w r947 1-216-825-11 metal chip 2.2k 5% 1/10w r948 1-216-825-11 metal chip 2.2k 5% 1/10w r949 1-216-825-11 metal chip 2.2k 5% 1/10w r950 1-216-825-11 metal chip 2.2k 5% 1/10w r951 1-216-845-11 metal chip 100k 5% 1/10w r952 1-216-825-11 metal chip 2.2k 5% 1/10w r953 1-216-825-11 metal chip 2.2k 5% 1/10w r954 1-216-845-11 metal chip 100k 5% 1/10w r955 1-216-864-11 short chip 0 r957 1-216-864-11 short chip 0 r960 1-216-817-11 metal chip 470 5% 1/10w r961 1-216-821-11 metal chip 1k 5% 1/10w r964 1-216-809-11 metal chip 100 5% 1/10w r965 1-216-797-11 metal chip 10 5% 1/10w r966 1-216-797-11 metal chip 10 5% 1/10w < vibrator > x802 1-813-940-11 piezoelectric oscillator (5.53mhz) ************************************************************* a-1244-295-a microphone board, complete (g770cpk) **************************** < capacitor > c408 1-165-176-11 ceramic chip 0.047uf 10% 16v c414 1-162-968-11 ceramic chip 0.0047uf 10% 50v < diode > d401 8-719-059-97 diode l-34hd (karaoke pon) < jack > j401 1-815-629-11 jack (mic mix) < coil > l303 1-410-509-11 inductor 10uh l304 1-410-517-11 inductor 47uh l305 1-410-509-11 inductor 10uh l308 1-410-509-11 inductor 10uh < resistor > r426 1-216-821-11 metal chip 1k 5% 1/10w r464 1-216-825-11 metal chip 2.2k 5% 1/10w r465 1-216-825-11 metal chip 2.2k 5% 1/10w r473 1-216-829-11 metal chip 4.7k 5% 1/10w < variable resistor > rv401 1-227-757-11 res, var, carbon 10k (mic level) < switch > s422 1-572-006-11 switch, push (1 key) (karaoke pon) ************************************************************* main microphone
66 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark a-1243-633-a power board, complete (us, cnd, mx, e92) a-1244-369-a power board, complete (sp, e41, aus) ********************** 1-533-233-31 fuse holder < capacitor > c901 1-163-037-11 ceramic chip 0.022uf 10% 50v c902 1-163-037-11 ceramic chip 0.022uf 10% 50v c903 1-163-037-11 ceramic chip 0.022uf 10% 50v c904 1-163-037-11 ceramic chip 0.022uf 10% 50v c909 1-126-943-11 elect 2200uf 20% 25v c927 1-100-591-91 ceramic chip 1uf 10% 25v c928 1-100-162-91 ceramic chip 1uf 50v < diode > d901 6-501-569-01 diode 1n5401-c352 d902 6-501-569-01 diode 1n5401-c352 d903 6-501-569-01 diode 1n5401-c352 d904 6-501-569-01 diode 1n5401-c352 ************************************************************* a-1244-294-a power key board, complete ************************** 3-831-441-11 cushion (b) < resistor > r399 1-216-817-11 metal chip 470 5% 1/10w r400 1-216-813-11 metal chip 220 5% 1/10w r408 1-216-821-11 metal chip 1k 5% 1/10w r455 1-216-809-11 metal chip 100 5% 1/10w < switch > s403 1-786-050-21 switch, key board (dspl/ent) s408 1-786-050-21 switch, key board (power) s410 1-786-050-21 switch, key board (sleep) ************************************************************* a-1246-280-a tc board, complete ****************** < capacitor > c101 1-162-964-11 ceramic chip 0.001uf 10% 50v c102 1-104-658-91 elect 100uf 20% 10v c103 1-165-176-11 ceramic chip 0.047uf 10% 16v c104 1-162-966-11 ceramic chip 0.0022uf 10% 50v c105 1-162-923-11 ceramic chip 47pf 5% 50v c107 1-162-962-11 ceramic chip 470pf 10% 50v c201 1-162-964-11 ceramic chip 0.001uf 10% 50v c202 1-104-658-91 elect 100uf 20% 10v c203 1-165-176-11 ceramic chip 0.047uf 10% 16v c204 1-162-966-11 ceramic chip 0.0022uf 10% 50v c205 1-162-923-11 ceramic chip 47pf 5% 50v c207 1-162-962-11 ceramic chip 470pf 10% 50v c301 1-104-658-91 elect 100uf 20% 10v c302 1-104-658-91 elect 100uf 20% 10v c303 1-104-658-91 elect 100uf 20% 10v c304 1-126-947-11 elect 47uf 20% 35v c305 1-162-962-11 ceramic chip 470pf 10% 50v c306 1-162-970-11 ceramic chip 0.01uf 10% 25v c307 1-162-964-11 ceramic chip 0.001uf 10% 50v < connector > cn303 1-568-830-11 connector, ffc 11p < ic > ic301 6-710-092-01 ic ta2068ng (5, hz) < jumper resistor > jc301 1-216-864-11 short chip 0 jc302 1-216-864-11 short chip 0 jc303 1-216-864-11 short chip 0 jc304 1-216-864-11 short chip 0 jc305 1-216-864-11 short chip 0 jc306 1-216-295-91 short chip 0 jc307 1-216-864-11 short chip 0 jc308 1-216-295-91 short chip 0 < transistor > q301 8-729-901-81 transistor 2sc2412k-t-146-r < resistor > r101 1-216-835-11 metal chip 15k 5% 1/10w r102 1-216-807-11 metal chip 68 5% 1/10w r103 1-216-843-11 metal chip 68k 5% 1/10w r104 1-216-835-11 metal chip 15k 5% 1/10w r105 1-216-835-11 metal chip 15k 5% 1/10w r106 1-216-825-11 metal chip 2.2k 5% 1/10w r110 1-216-809-11 metal chip 100 5% 1/10w r111 1-216-829-11 metal chip 4.7k 5% 1/10w r112 1-216-827-11 metal chip 3.3k 5% 1/10w r201 1-216-835-11 metal chip 15k 5% 1/10w r202 1-216-807-11 metal chip 68 5% 1/10w r203 1-216-843-11 metal chip 68k 5% 1/10w r204 1-216-835-11 metal chip 15k 5% 1/10w r205 1-216-835-11 metal chip 15k 5% 1/10w r206 1-216-825-11 metal chip 2.2k 5% 1/10w r210 1-216-025-11 res-chip 100 5% 1/10w r211 1-216-829-11 metal chip 4.7k 5% 1/10w r212 1-216-827-11 metal chip 3.3k 5% 1/10w r301 1-216-857-11 metal chip 1m 5% 1/10w r302 1-216-829-11 metal chip 4.7k 5% 1/10w r303 1-216-829-11 metal chip 4.7k 5% 1/10w r304 1-216-821-11 metal chip 1k 5% 1/10w r305 1-216-817-11 metal chip 470 5% 1/10w r306 1-218-867-11 metal chip 6.8k 0.5% 1/10w r307 1-216-797-11 metal chip 10 5% 1/10w r308 1-216-837-11 metal chip 22k 5% 1/10w r309 1-216-805-11 metal chip 47 5% 1/10w r314 1-216-817-11 metal chip 470 5% 1/10w r315 1-216-817-11 metal chip 470 5% 1/10w < switch > s301 1-786-126-11 switch, slide (rec/pb) power power key tc
67 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark < transformer > t301 1-416-041-11 transformer, bias oscillation ************************************************************* a-1244-418-a tuner board, complete (us, cnd, mx, e92) a-1244-419-a tuner board, complete (sp, e41, aus) ********************** 2-895-061-01 terminal, antenna < capacitor > c1 1-162-923-11 ceramic chip 47pf 5% 50v c4 1-162-964-11 ceramic chip 0.001uf 10% 50v c7 1-162-910-11 ceramic chip 5pf 0.25pf 50v c8 1-162-964-11 ceramic chip 0.001uf 10% 50v c9 1-162-915-11 ceramic chip 10pf 0.5pf 50v c10 1-126-960-11 elect 1uf 20% 50v c11 1-107-826-11 ceramic chip 0.1uf 10% 16v c12 1-126-963-11 elect 4.7uf 20% 50v c13 1-162-970-11 ceramic chip 0.01uf 10% 25v (us, cnd, mx, e92) c14 1-162-970-11 ceramic chip 0.01uf 10% 25v (sp, e41, aus) c14 1-164-227-11 ceramic chip 0.022uf 10% 25v (us, cnd, mx, e92) c15 1-162-970-11 ceramic chip 0.01uf 10% 25v (sp, e41, aus) c15 1-164-227-11 ceramic chip 0.022uf 10% 25v (us, cnd, mx, e92) c18 1-126-923-91 elect 220uf 20% 10v c20 1-107-826-11 ceramic chip 0.1uf 10% 16v c21 1-126-960-11 elect 1uf 20% 50v c22 1-107-826-11 ceramic chip 0.1uf 10% 16v c23 1-126-960-11 elect 1uf 20% 50v c24 1-162-960-11 ceramic chip 220pf 10% 50v c26 1-162-927-11 ceramic chip 100pf 5% 50v c27 1-162-927-11 ceramic chip 100pf 5% 50v c29 1-104-658-91 elect 100uf 20% 10v c30 1-162-970-11 ceramic chip 0.01uf 10% 25v c31 1-162-919-11 ceramic chip 22pf 5% 50v c32 1-162-964-11 ceramic chip 0.001uf 10% 50v c33 1-162-970-11 ceramic chip 0.01uf 10% 25v c34 1-162-970-11 ceramic chip 0.01uf 10% 25v c35 1-162-970-11 ceramic chip 0.01uf 10% 25v c37 1-162-970-11 ceramic chip 0.01uf 10% 25v c39 1-107-826-11 ceramic chip 0.1uf 10% 16v c41 1-164-230-11 ceramic chip 220pf 5% 50v c42 1-162-927-11 ceramic chip 100pf 5% 50v c43 1-162-919-11 ceramic chip 22pf 5% 50v c47 1-162-915-11 ceramic chip 10pf 0.5pf 50v c49 1-161-051-00 ceramic 0.01uf 10% 25v c51 1-162-919-11 ceramic chip 22pf 5% 50v c52 1-162-915-11 ceramic chip 10pf 0.5pf 50v c53 1-137-190-91 film 0.22uf 5% 50v c54 1-126-923-91 elect 220uf 20% 10v c55 1-162-927-11 ceramic chip 100pf 5% 50v c56 1-162-964-11 ceramic chip 0.001uf 10% 50v c57 1-162-964-11 ceramic chip 0.001uf 10% 50v c59 1-162-927-11 ceramic chip 100pf 5% 50v c60 1-162-964-11 ceramic chip 0.001uf 10% 50v c61 1-162-927-11 ceramic chip 100pf 5% 50v c62 1-162-927-11 ceramic chip 100pf 5% 50v c63 1-162-927-11 ceramic chip 100pf 5% 50v c65 1-126-963-11 elect 4.7uf 20% 50v c66 1-162-927-11 ceramic chip 100pf 5% 50v c68 1-162-927-11 ceramic chip 100pf 5% 50v c77 1-162-968-11 ceramic chip 0.0047uf 10% 50v (sp, e41, aus) c78 1-162-968-11 ceramic chip 0.0047uf 10% 50v (sp, e41, aus) c80 1-162-970-11 ceramic chip 0.01uf 10% 25v c95 1-162-964-11 ceramic chip 0.001uf 10% 50v < filter > cf2 1-760-235-81 filter, ceramic cf4 1-781-962-21 filter, ceramic < connector > cnp1 1-568-854-11 connector, ffc 11p < trimmer > ct1 1-141-442-91 cap, ceramic trimmer 20pf ct3 1-141-304-21 cap, ceramic trimmer 10pf < diode > d1 8-719-078-48 diode kv1471etr-g d2 8-719-078-48 diode kv1471etr-g d3 8-719-050-69 diode kv1520n d10 8-719-988-61 diode 1ss355te-17 d11 8-719-988-61 diode 1ss355te-17 < ic > ic1 6-700-512-01 ic ta2149bn ic2 8-759-483-40 ic lc72137m-tlm-e < jumper resistor > jc1 1-216-864-11 short chip 0 jc2 1-216-864-11 short chip 0 jc3 1-216-864-11 short chip 0 jc4 1-216-864-11 short chip 0 jc5 1-216-864-11 short chip 0 jc6 1-216-864-11 short chip 0 jc11 1-216-864-11 short chip 0 jc12 1-216-864-11 short chip 0 jc13 1-216-864-11 short chip 0 jc24 1-216-864-11 short chip 0 (sp, e41, aus) jc33 1-216-864-11 short chip 0 jc34 1-216-864-11 short chip 0 < coil > l1 1-409-775-11 coil, air-core l2 1-416-509-11 coil, air-core l3 1-754-117-12 antenna, ferrite-rod (mw) l4 1-411-234-21 coil, am osc l11 1-414-142-11 inductor 1uh (us, cnd, mx, e92) tuner tc
68 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark ref. no. part no. description remark l21 1-410-509-11 inductor 10uh < resistor > r1 1-216-817-11 metal chip 470 5% 1/10w r2 1-216-817-11 metal chip 470 5% 1/10w r3 1-216-833-11 metal chip 10k 5% 1/10w r4 1-216-833-11 metal chip 10k 5% 1/10w r5 1-216-821-11 metal chip 1k 5% 1/10w r10 1-216-805-11 metal chip 47 5% 1/10w r11 1-216-825-11 metal chip 2.2k 5% 1/10w r13 1-216-821-11 metal chip 1k 5% 1/10w r14 1-216-821-11 metal chip 1k 5% 1/10w r24 1-216-813-11 metal chip 220 5% 1/10w r30 1-216-837-11 metal chip 22k 5% 1/10w r31 1-216-829-11 metal chip 4.7k 5% 1/10w r32 1-216-845-11 metal chip 100k 5% 1/10w r33 1-216-833-11 metal chip 10k 5% 1/10w r40 1-216-849-11 metal chip 220k 5% 1/10w r41 1-216-833-11 metal chip 10k 5% 1/10w r50 1-216-821-11 metal chip 1k 5% 1/10w r51 1-216-833-11 metal chip 10k 5% 1/10w r52 1-216-864-11 short chip 0 r53 1-216-829-11 metal chip 4.7k 5% 1/10w r54 1-216-817-11 metal chip 470 5% 1/10w r55 1-216-833-11 metal chip 10k 5% 1/10w r56 1-216-813-11 metal chip 220 5% 1/10w r57 1-216-809-11 metal chip 100 5% 1/10w r58 1-216-825-11 metal chip 2.2k 5% 1/10w r59 1-216-825-11 metal chip 2.2k 5% 1/10w r60 1-216-825-11 metal chip 2.2k 5% 1/10w r61 1-216-825-11 metal chip 2.2k 5% 1/10w r63 1-216-833-11 metal chip 10k 5% 1/10w r65 1-216-833-11 metal chip 10k 5% 1/10w r91 1-216-813-11 metal chip 220 5% 1/10w r92 1-216-813-11 metal chip 220 5% 1/10w r94 1-216-821-11 metal chip 1k 5% 1/10w < transformer > t1 1-433-741-11 transformer, if t2 1-419-465-11 coil (det) < vibrator > x1 1-795-449-11 vibrator, crystal (75khz) ************************************************************* a-1244-293-a volume key board, complete *************************** 3-831-441-11 cushion (b) < resistor > r411 1-216-813-11 metal chip 220 5% 1/10w r412 1-216-817-11 metal chip 470 5% 1/10w r413 1-216-821-11 metal chip 1k 5% 1/10w r414 1-216-821-11 metal chip 1k 5% 1/10w r415 1-216-825-11 metal chip 2.2k 5% 1/10w r425 1-216-825-11 metal chip 2.2k 5% 1/10w r443 1-216-821-11 metal chip 1k 5% 1/10w r458 1-216-809-11 metal chip 100 5% 1/10w < switch > s404 1-786-050-21 switch, key board (mode) s407 1-786-050-21 switch, key board (vol+) s411 1-786-050-21 switch, key board (auto preset radio/band) s412 1-786-050-21 switch, key board (audio in) s418 1-786-050-21 switch, key board (repeat) s420 1-786-050-21 switch, key board (vol? ************************************************************* a-1244-298-a woofer key board, complete *************************** 3-831-441-11 cushion (b) < connector > cnp401 1-815-443-11 pin, connector (pwb) 2p < resistor > r401 1-216-813-11 metal chip 220 5% 1/10w r402 1-216-817-11 metal chip 470 5% 1/10w r403 1-216-821-11 metal chip 1k 5% 1/10w r416 1-216-825-11 metal chip 2.2k 5% 1/10w r417 1-216-821-11 metal chip 1k 5% 1/10w r423 1-216-821-11 metal chip 1k 5% 1/10w r424 1-216-825-11 metal chip 2.2k 5% 1/10w r459 1-216-809-11 metal chip 100 5% 1/10w < switch > s409 1-786-050-21 switch, key board (rock) s415 1-786-050-21 switch, key board (dance) s416 1-786-050-21 switch, key board (salsa) s417 1-786-050-21 switch, key board (flat) s419 1-786-050-21 switch, key board (power drive woofer) s421 1-786-050-21 switch, key board (reggaeton) ************************************************************* miscellaneous ************** 0 160 8-820-126-02 optical pick-up (ksm-213cdp/c2np) 164 1-832-404-21 cable, flexible flat (16 core) 166 1-832-613-21 cable, flexible flat (21 core) 205 1-754-376-11 antenna, telescopic 206 1-452-899-11 magnet 253 1-797-375-11 deck, mechanical (h21sb-c05) cnp2 1-833-922-11 cord, connection (with plug) d403 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d404 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d405 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d407 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d408 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d409 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d410 6-501-452-01 diode 1l4345v22dotdt02 (illumination) d411 6-501-452-01 diode 1l4345v22dotdt02 (illumination) 0 f902 1-532-504-33 fuse (t4al/250v) tuner v olume key w oofer key
69 CFD-G700CP/g770cp/g770cpk ref. no. part no. description remark 0 j901 1-526-838-11 inlet, ac 2p ( - ac in) (sp, e41, aus) 0 j901 1-540-009-11 inlet, ac ( - ac in) (us, cnd, mx, e92) s201 1-771-853-11 switch, detection (limit) sp191 1-826-684-11 speaker (10cm) sp291 1-826-684-11 speaker (10cm) sp393 1-826-683-11 speaker (13cm) sw2 1-692-960-11 switch, push (1 key) ( z push open/close) 0 t901 1-435-964-12 transformer, power (us, cnd, mx, e92) 0 t901 1-435-965-12 transformer, power (sp, e41, aus) ************************************************************* accessories *********** a-1246-031-a remote commander (rmt-cg700a) (including battery case) 0 1-769-412-22 cord, power (g770cp) 0 1-782-126-11 cord, power (us, cnd, mx, e92) 0 1-827-945-12 cord, power (aus) 3-096-718-11 manual, instruction (english) (g700cp) 3-096-718-21 manual, instruction (english, spanish) (e92) 3-096-718-31 manual, instruction (english, french) (sp) 3-096-718-41 manual, instruction (spanish) (e41) 3-096-718-51 manual, instruction (english) (aus) 3-096-718-61 manual, instruction (english, french) (cnd) 3-096-718-71 manual, instruction (spanish) (mx)
CFD-G700CP/g770cp/g770cpk revision history clicking the version allows you to jump to the revised page. also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. ve r. date description of revision 1.0 2007.03 new

▲Up To Search▲

Price & Availability of CFD-G700CP

	To Download CFD-G700CP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .